ThE_BaNsHeE_mAn88

im going to a track next week and ill get some pics for this. oh and that bike above me that thing is tits.

i think the stock tires suck that bad. the way i take a turn like that is come into it and slip the clutch half way thro it and slide it allways works for me. but i would get some new back tires and then try it.

i just got mine today im going to run them on stock arms and ill let you know what there like. oh and i do plan on getting +2+1 J-arms

i use future floor wax it works good for shine and scratches.

pm sent on the nerfs

dude where was this a month ago when i was looking for one. but anyways thats a good price and hope you can sell it .free bump

i have a banshee with a freash motor not even 5hours on it. all the mods are below.

its a bitch ::

okay i was woundering if you would get rid of the boots without the bike?

i need some nerfs for my she and some boots for me. i wear size 12 and any kind of boot will be good. i would like to get them cheap and in good shape. if you have anything give me a price and ill see.

i got stockers with red springs $50

dude i think the best back up bike is the blaster my friend also has one of thoes and that thing takes a beating. i mean his bike broke down this winter and we kick the shit out of it all winter long and it still runs like a champ all you got to do is put gas and oil in it and your good to go. oh and the raptor is 33in wide in the rear and 36in wide in the front so that could have something to do with it being so tippy :yelrotflmao:

i just road a raptor 660 the other day and the power is awsome and it pulls hard. it stock with the pipe gutted out. the power is good but the thing handles like crap!!!!!it tips way to easy and the thing just doesnt take corners good at all.if you dont get the back end loose befor you go into a corner your probly going to tip. well thats what i think about it whats your guys thought.

my friend has a pair of triple rates on his z and he loves them. good shocks.

well if something didnt get done right im going to be pissed but i hope thats not the problem.

i guess ill test it with another tester and see what it says. but i still dont know why it wont run?

see the thing is that it just was rebult and it had 75psi when i got it back so....

the compression is 75psi in both and i put new plugs in both sides so i have no idea :shrug: i check the fuel lines and there clean and i check the one side reeds and carbs but not the other so.... but if you have any ideaor suggestions it would be great. oh and when i was mixing the oil there was clomps of oil and i use klotz super technaplate 20% castoroil so i put it in thinking it would dissolve is it posible that the oil could be plug the jets? Derick

ok i got my bike running good and tookit for a little ride. it was hot out (90degrees)and shee started to pop and cut out and shit. well i figured shee was getting hot so i shut her off ans 5min later i started it again and it ran fo 30sec and died and now it wont start. its a barned new motor :: . my did was messing with it and put a cap full of gas in each cylinder and it started and then ran out. it has a full tank of gas so idk whats going on with it.so if i could get some help it would be nice. just through out some suggestion. Derick

thoes bars look good but i personly love fat bars i have a set of trail tech x bars and i love them.

im haveing a prblem were my left cylinder wont run at an idle but once you get the rpms up is runs good. could the crossover tube be cloged and just make the left side foold?

bump

ok got my bike back again and it runs decent at higher rpms and when your going and let off the right side cuts out and then you get on it and it pops once and kicks back on. but at an idel the right side wont run at all. i have no idea because the guy put a crab off an 06 shee never used and its still doing it. :angry:the builder said he put alot of oil in the cylnders could that be th problem? could it just be loading up? and should i just run it to clean it out?

i have a 210 main and i dont know what the others are. but when i first tryed to start it the right side didnt run so the slids were in backwards and then i switched them and then the left side stoped running so........ i dont know whats going on. but i brough the hole bike back to the bulder so he can figure it out.but any more help would be great. thanks.oh and is there susposed to be gas going through the choke tube?????

ok i just got my motor back from being rebult and i started it up for the first time. and the laft side wont run consistant. it will pop ever once and a while and shoots oil and gas out. i dont think is fluded because i have put like 5 plugs in the one side. i adjusted the slides, they were in the wrong way at first but there in the right way now. so any help will be great thanks.