quickturbo

Did you find out what year it is or get pics?

Where are you located? and what year is the roller?

He finally emailed me back on 4/4 and said he sent the wheels and I shoud see them buy 4/7 but I still havent seen anything.

I sent you a PM.

Do you have any pics? Could you send them to [email protected] Is there anything aftermarket on it?

I sent him money for some wheels/tires I never received anything. The last time I was able to get in contact with him he said he received my Money Order and would get me shipping confirmation # but I never heard from him again.

The strange thing about it is I just found a set of the same tires and wheels with about the same tread and the same size as the pics he sent me for sale on ebay for the same price but they are in NJ but the Money order I sent him is to greentop, mo. This may be just chance but the pics on ebay and the pics he sent me look alot alike. I hope this is just a weard chance or I'm out $100.

Has everyone gotten there things from sand-dragon7379?? I still havent recieved my wheels/tires. I've emailed him a few times this last week with no replies. The last reply I recieved was on 3/13.

I sent him a money order for the rear tires/wheels on tuesday. I will post if I have any problems but so far he has returned my emails.

I might be interested in the rear tires/wheels could you please get me some pics? Also are there any plugs or leaks in the tires? What bolt pattern are the wheels? My email [email protected]

Where in Pa are you and do you have any pics?

I am having a hard time getting my carbs to idle correctly. They seem to be running lean and I have moved the needle clip to the bottom ring with only a very little help. I played with the pilot air screws and I had them up to 4 1/2 turns out and still not rich enough. At full/mid throttle it seems OK I have many different main jets just no pilot jets. Does anyone have any other suggestions? My mods are -fmf exhaust -filter with no air box lid -cylinders bored to 30 over

What are you looking for the headlights?

Does the motor turn over?? Where are you located?

I sent you a PM

I sent you a PM about the carbs

What were you looking to get for the carbs?

Thanks for the info so far To answer some of the replys I have changed the crossover tube but it didnt help and I have put in a few sets of new plugs and I tried 2 coils but both give the same problem. I think I have it narrowed down to the Carb but Im not sure whats wrong with it. I put in new jets (all of them) new main needle new needle/seat for the float the left carb seems to be working great its just the right side.

I started the Banshee up today and it still loads up on the right side. It idels OK and full throttle is OK but the mid section will shot gas out the pipe. Both the carbs are set up the exact same way. Does anybody have any other ideas??

Thanks for the replys Here is what I tried since the last email Removed the carb and took apart but didnt see anything wrong Took reeds out but they look fine The needle is already on the 2nd clip down in the carbs. I did notice the choke hose that goes from one carb to the other is getting a little soft and not fitting so good. I havent tried to start it since.

souva91 I sent you a PM

My banshee has a miss on the right side jug. I reversed the plug wires but still no help. I have great compression on both jugs and both carbs are set up the same and just rebuilt. It idles fine and is great at full throttle but the mid range it just gets loaded up and nothing but gas/oil come out the pipes. Any ideas?? Thanks

Does anyone have a good kicker idler gear laying around. I am trying to get my banshee running but I found the bushing in the idler gear is shot.

What do you want for the frame skid and A arm skids?

Will the stock thumb throttle cable work with a carb setup without the TORS? I have a twist throttle on now and want to put a thumb throttle on. Thanks