01bansheefox

Is that a set for everything on a banshee? Seat?Tank?Fenders?Pipes etc....? Also does it come labled?

Ok i need some bolts and other items that are missing from my shee. I do not want to go to the dealership because I bet more than anything it will be about $5 per bolt. What sizes do i need for my gas tank? I has 0 nuts/bolts along with my fenders? Or when you buy new fenders do they send bolts & nuts?

Looking for a pair plzzzz

Hmm I fixed it I guess, i just kept hitting it with my hand and it pushed itself back down into place, and is now level.

Ok hmmm thats right then The kit came with one big Rubber ring that fits the outside, also how do i get that to stick? it fits just a bit loose, also.... 2 small rings that fit around the piston and then 2 exhaust gaskets, 2 intake gaskets and the 1 big cylinder gasket.

umm actually looking through everything there isnt even a gasket that fits where the head bolts up to, shouldnt there be one? The gasket that i thought was for the head is the cylinder gasket where they bolt to the motor.

Just got my top end gasket kit. The kit is for the ProX single head 409 kit. I got a rubber ring that goes along the outside of the head, does this come before or after the gasket? No instructions came with the kit.

Ok how do i put it back in? Just push with pressure?

Go here http://www.nossmachine.com/banshee_heads.htm scroll down to the 3rd picture It shows the head upside down with the domes, My dome on the left side is not flush like it is not in all the way, it sticks out about the width of a needle.

I do not have a camera with me.... Isnt is the dome? Ok i took off my head of a ProX Bigbore 409 Its a solid head that has 2 domes, if you flip the head upside down so you see the bottom of the spark plugs, the dome looking thing is not even with the smooth surface. I dont know how else to explain it... If you run your fingernail across the bottom surface of the head it will catch on a dome because it doesnt sit inside all the way.

Flip your head upside down where you can see the bottom of your plug. That circle dome is not even with the head it hangs down like ??? width of a needle. Its just not even put it that way.

Well how do i put it back down? I guess it has been running like this because this is how it was when i just pulled the head off.

Pulled off the head, and one dome sits up about the size of a dime or a little smaller. It isnt flush with the head. This a big issue? and how do I fix it, if needed.

I have the ProX 409 head but there tech dude is out for the whole week, How tight should I go?

race cut in front, rear doesnt matter.

Its already been shipped its in my garage right now but it needs a new head gasket and some others. Also..... One of the domes? isnt smooth with the head it sticks up maybe the size of a needle.

Beats me.... im in Sacramento California 200?

Just bought a banshee off ebay from Florida do I need to change any of that stuff due to the elevation etc.....

Well then it has to be compression. I took off the head and there isnt a head gasket, just some homemade silicon shit, Should i replace the pistons and rings? They do not look dammaged in anyshape, I just have no gaskets on it now.

Yes it was shipped that must be the reason because everything else was out of fluid. Its not seized, it wont start though but backfires maybe 1/10 kicks. I just pulled the head off and it looks as if water was on top of the piston? like muddy water and the idiot didnt have a seal on the head it was some homemade silicon shit.

The link goes to a Kenwood amp?

As most of u know i got the 400 stroker ebay banshee, it had water inside and no head gasket for some reason? He used like homemade cilicon.. anyway im just gonna redo the pistons and rings. Where can i find a kit for it? The engine is the Pro X 400 big bore.

It's very stuck.... with the old gasket and some type of gasket goop. Its a head from LA Sleevs 400big bore kit. Do i keep putting presure by prying it with a bar/screw driver?

Some of you have probably seen my other post, i just got the banshee of of ebay and there is no water in radiator and he also has some other little container set up for some reason for like extra water for the radiator, both things are empty, lets say the engine melted from heat, is that fixable?

It has good spark and fuel.