bansheepartsguy Posted February 27, 2007 Report Posted February 27, 2007 I was curious if anyone would know what exhaust setup would work best for a 10 mil stroker, 70mm piston trinity big bore kit. I will be running race gas, 35.5mm mikuni flat slide carbs, v-force, 36mil billet intakes, lockup clutch, ect. I want to run an out of frame drag pipe. Should I get big or small bore pipes with this setup? I think it's round about a 470cc. CPI or Shearer? Are ftz pipes any good? RDZ? Thanks, Lance Quote
locogato11283 Posted February 27, 2007 Report Posted February 27, 2007 im runnin rocket pipes on my 10mm 68mm cub... they seem to run pretty well. i would go with shearer over cpi but if youre willing to wait a couple months there is a new pipe coming out that ran real hard on my 10mm cub.. they had a lot of bottom end and pulled very hard on top.. Quote
bansheepartsguy Posted February 27, 2007 Author Report Posted February 27, 2007 im runnin rocket pipes on my 10mm 68mm cub... they seem to run pretty well. i would go with shearer over cpi but if youre willing to wait a couple months there is a new pipe coming out that ran real hard on my 10mm cub.. they had a lot of bottom end and pulled very hard on top.. i'm not familiar with rocket pipes. Who makes them. Do they have a website. Who makes the new pipes that your talking abuot. Are the rocket pipes big bore? Quote
FireHead Posted February 27, 2007 Report Posted February 27, 2007 I was curious if anyone would know what exhaust setup would work best for a 10 mil stroker, 70mm piston trinity big bore kit. I will be running race gas, 35.5mm mikuni flat slide carbs, v-force, 36mil billet intakes, lockup clutch, ect. I want to run an out of frame drag pipe. Should I get big or small bore pipes with this setup? I think it's round about a 470cc. CPI or Shearer? Are ftz pipes any good? RDZ? Thanks, Lance Since you are running stock cylinders I recommmend small bore pipes. Like I said in the PM we can run through the math if you want. You need to move a certain amount of air at a certain frequency for an expansion chamber to be efficient. There are alot of people running big bore pipes for no good reason. If you want the best pipe for you motor then you need to have a set custom made for you motor. If you want the best pipe you can buy off the shelf, then that is a different story. The Grand River Racing pipes are nice along with Wicked pipes. I am not a fan of FTZ or RDZ pipes, but i don't really have a good reason for that. Shearer's are good as always and so are CPI's. :thumbsup: Quote
dajogejr Posted February 27, 2007 Report Posted February 27, 2007 Dude....you got this same question listed here, in the drag forum AND the sand forum.... Yep...we need some mods to clean stuff like this up, Loco...know what I'm sayin? http://www.bansheehq.com/forums/index.php?showtopic=74509 http://www.bansheehq.com/forums/index.php?showtopic=74510 Quote
locogato11283 Posted February 27, 2007 Report Posted February 27, 2007 Dude....you got this same question listed here, in the drag forum AND the sand forum.... Yep...we need some mods to clean stuff like this up, Loco...know what I'm sayin? http://www.bansheehq.com/forums/index.php?showtopic=74509 http://www.bansheehq.com/forums/index.php?showtopic=74510 yea its pretty fuckin ridiculous.. Lee is apparently ignoring it because ive said something about it in several different posts several different times. maybe we need to start a thread simply for that in website issues or site announcements. i guess i dont see why it would be so hard to appoint a few mods to clean shit up. Quote
bansheepartsguy Posted February 27, 2007 Author Report Posted February 27, 2007 I apologise. I just wanted alot of people to see it. I didn't know that I wasn't supposed to do that. My bad. It wont happen again. Sorry... Quote
FireHead Posted February 27, 2007 Report Posted February 27, 2007 yea its pretty fuckin ridiculous.. Lee is apparently ignoring it because ive said something about it in several different posts several different times. maybe we need to start a thread simply for that in website issues or site announcements. i guess i dont see why it would be so hard to appoint a few mods to clean shit up. What the hell...........the dude also sent me PM's about that shit. I think I replied to all of them, not really paying attention and seeing it the same person. I want a refund for my personal time. :verymad: Quote
bansheepartsguy Posted February 27, 2007 Author Report Posted February 27, 2007 (edited) What the hell...........the dude also sent me PM's about that shit. I think I replied to all of them, not really paying attention and seeing it the same person. I want a refund for my personal time. :verymad: sorry man, I had already apologised... I'm new here... I do appreciate the help... :ermm: Edited February 27, 2007 by bansheepartsguy Quote
FireHead Posted February 28, 2007 Report Posted February 28, 2007 sorry man, I had already apologised... I'm new here... I do appreciate the help... :ermm: No worries........I was ju8st being dramatic. :thumbsup: Quote
gipperz Posted March 1, 2007 Report Posted March 1, 2007 im runnin rocket pipes on my 10mm 68mm cub... they seem to run pretty well. i would go with shearer over cpi but if youre willing to wait a couple months there is a new pipe coming out that ran real hard on my 10mm cub.. they had a lot of bottom end and pulled very hard on top.. Interesting Loco, keep me informed if you will. :biggrin: Quote
locogato11283 Posted March 1, 2007 Report Posted March 1, 2007 Interesting Loco, keep me informed if you will. :biggrin: cory, i will for sure.. i should know more here in a month or so.. Quote
dajogejr Posted March 1, 2007 Report Posted March 1, 2007 cory, i will for sure.. i should know more here in a month or so.. You've peaked my interest as well....keep me in the loop as well... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.