no spark

[99bansheeworked]

i had my friend look at my quad i took the case where the oil is out to put a new gasket back on i put the kickstater back and put oil in it and there is no spark at all i check all the wires on the cdi box and there all good no cut wires at all what do you think that the prolbem is thank you

[AKheathen]

i had my friend look at my quad i took the case where the oil is out to put a new gasket back on i put the kickstater back and put oil in it and there is no spark at all i check all the wires on the cdi box and there all good no cut wires at all what do you think that the prolbem is thank you

hello, so what you're sayin is all you did is replace the clutch cover gasket right? it probably is just the kill circut. push on the throttle a little when you check for spark, if it sparks, then the carb wires are disconnected somehow. you can either fix it, or unpug the 3 wire connector going to the little box under the gas tank across from the coil to eliminate the tors circut. if not, check the black wire on the coil with a meter to make sure it has good ground to the frame and engine block. also ckeck the black/white wire at the cdi for ground, if you have contact with ground, it will kill the spark. think of anything else that could've been messed with while working on it.

 

if that doesn't help, give more info on what you find, and we can point you tward some more things

[99bansheeworked]

hello, so what you're sayin is all you did is replace the clutch cover gasket right? it probably is just the kill circut. push on the throttle a little when you check for spark, if it sparks, then the carb wires are disconnected somehow. you can either fix it, or unpug the 3 wire connector going to the little box under the gas tank across from the coil to eliminate the tors circut. if not, check the black wire on the coil with a meter to make sure it has good ground to the frame and engine block. also ckeck the black/white wire at the cdi for ground, if you have contact with ground, it will kill the spark. think of anything else that could've been messed with while working on it.

 

if that doesn't help, give more info on what you find, and we can point you tward some more things

 

there is no kill switch on the quad and i checked all the wires on the cdi box and they are all connected correctly, all i did was put a new gasket where the magnito is and took out the kickstarter to put the new gasket in then reattatched the kickstarter and found out that there was no spark.

[AKheathen]

there is no kill switch on the quad and i checked all the wires on the cdi box and they are all connected correctly, all i did was put a new gasket where the magnito is and took out the kickstarter to put the new gasket in then reattatched the kickstarter and found out that there was no spark.

i said the black/whitewire is the kill wire that is used by all circuts including key and tors. it needs to have no contact to run. the kick starter is on the clutch side, and the magneto is on the other, so are you sayin that you replacd both? ohm the stator and pickup wires

[99bansheeworked]

i said the black/whitewire is the kill wire that is used by all circuts including key and tors. it needs to have no contact to run. the kick starter is on the clutch side, and the magneto is on the other, so are you sayin that you replacd both? ohm the stator and pickup wires

 

what i mean when i got it there no kill switch u had to stall it out and stuf like that all i did was change teh gasket out and put a new 1 where hte oil is put that in then kickstart there no spark idk y

[skinindustries]

you should try to unhook the TORS system it is right next to the coil on the left i had no spark and i unhooked that today and bam i got spark now