360Bansheelab

Yes it's a cheetah with cast cylinder luckily for me it's not nikasil so it can be bored.

Your right, found the original build sheet. It's a 64mm stroke with Wiseco 71.92mm pistons. Louie from Twister is currently trying to locate a set. Apparently there is something abnormal about them and aren't that easy to locate.

712M07250 look like they are for a 73mm stroke and require nykasil cylinders 536M07250 look like they are for a 60mm stroke. I have a 63mm stroke because of the 125mm rods. Any other ideas? Thanks for the input guys

No windows in them. :-)

Awesome! Thank you.

Ok I no this page is full of knowledge and need some help. I just restored a banshee with a 10mil Cheetah in it. I removed the PV and had the motor gone through by a local shop. On the second time out it began to run like crap, so I took it back to the shop. They tore into it and discovered the one of my reeds (VForce 2) had a broken pedal. With further review they discovered that one of the screws (typical) came loose from the reed and took out my piston and dome. Where is where I need advice... It has 125mm rods, 72.5 pistons with 18mm wrist pins. I have been told that these pistons with 18mm wrist pins are obsolete and only a couple left in existence and cost $350-400.00 a pair. Is that true? Does anyone know of a vendor that I can find these? Thanks in advance

The bike is still at the shop, I should have it back in a few days so I can get the number off the piston then. I haven't called anyone yet, just thought I would ask around in the meantime.

Ok I no this page is full of knowledge and need some help. I just restored a banshee with a 10mil Cheetah in it. I removed the PV and had the motor gone through by a local shop. On the second time out it began to run like crap, so I took it back to the shop. They tore into it and discovered the one of my reeds (VForce 2) had a broken pedal. With further review they discovered that one of the screws (typical) came loose from the reed and took out my piston and dome. Where is where I need advice... It has 125mm rods, 72.5 pistons with 18mm wrist pins. I have been told that pistons with 18mm wrist pins are obsolete and only a couple left in existence and cost $350-400.00 a pair. Is that true? Does anyone know of a vendor that I can find these? Thanks in advance.

I have a 10mil 72 bore 521cc Cheetah

How much for the bowls?

I am in the market for a new set of big bore Shearer pipes and have attempted to contact Nearly every dealer on this website even Shearer directly. Not a single retailer has answered the phone, replied to my voice or email. Have any of you ran into this issue? Any recommendations on a supplier I should contact? Thanks in advance.

Looking for a nice set of Big Bore In Frame Shearer exhaust. Cash in hand Thanks in advance.

I am looking for a nice, clean complete set. Thanks in advance

Sold!!! Thanks loosechange

I would prefer to trade them, but make an offer.

I have a very nice set of CPI small bore pipes, stingers and silencers that I am looking to trade for a set of BIG Bore Shearer. I would like a full set that includes stingers and silencers. I would prefer trade, but willing to buy outright if needed. The pipes are shown in my sig, I will add a photo later or can email/text one to you. Thanks in advance.

Sold

Here is a pic

I have a lightly used set of 38 Airstrikers. I painted the bodies gloss black and polished the bowls. They look nice. $225.00 shipped

Sold. Thanks V2

Sale pending. Thanks for the interest

Sale pending. Thanks for the interest

Sold it. Thanks for the interest

Trade pending. Thanks S&L Performance

Drag cut