kevincurtis

It's a aftermarket stator, i checked the pick-up gap and its within spec at both nubs, and both boots are fine im running pro design manifolds.. usually i have no problem figuring things out but this one is frustrating must be something im forgetting..

Hey guys, I followed through with the info yous gave me and i still have no luck.. I'm stumped ! its running richer on one cylinder... i cleaned carbs, jetting is the same in both, checked reeds, did another leak down.. i swapped cdi & coil, also ran a ground from coil to motor i tested stator and it reads correct ohms.. could the stator possibly still be bad ? Whats going on ? Any more info would be greatly appreciated !

My banshee is working quite bad.. Cutting out, and not pulling at all quite weird as my jetting was perfect, I did a leak down and checked over everything fuel / air related and everything seems to be fine. I went down the road a while ago with it and it was still working bad and as I got up in the mid / top end range it was like nothing was wrong it cleaned right up and Pulled like a @$#ker ,it did it once more than right back to working like shit ! I tested my stator right away and it was fine.. If someone could point me in the right direction of where to start that would be great.. Thank you

No actually I'm running the Vito's big bore 13 degree angle domes and pistons, if I decide on pump fuel looks like I'll need some custom domes.. Like you said pluses and minuses for both

My current squish is .042, I'm using Vito's 13 degree dome angle domes. Squish is within spec

I just recently got my 421 together, I'm running it with pump 91 octane with pro design cool head and 24 cc domes at sea level. i did a compression test today and my compression raised to 160 psi after break-in, i know its quite high for 91 octane, and my timing is still at 0" I want to advance it 4 degrees.. i'm thinking I'll have to get some custom domes to run pump fuel, but if i was to run a higher octane what would you's recommend i run ? just curious because this is my first time playing with my bike with the compression bumped up, Any info would be great thanks !

I just recently got my 421 together, I'm running it with pump 91 octane with pro design cool head and 24 cc domes at sea level. i did a compression test today and my compression raised to 160 psi after break-in, i know its quite high for 91 octane, and my timing is still at 0" I want to advance it 4 degrees.. i'm thinking I'll have to get some custom domes to run pump fuel, but if i was to run a higher octane what would you's recommend i run ? just curious because this is my first time playing with my bike with the compression bumped up, Any info would be great thanks !

I'm quite interested in the serval I've been reading some good stuff about them, I was looking on the CP site and didn't see them there ? Does CP industries make servals ? or does someone else, I see them on ebay but was curious as to who manufactures them ?

That would be nice to have at a pump, not that lucky around here unfortunately, I might go try the local drag track See if they carry 94

Yes that's what I got on my comp check with a cold engine

I'm from New Brunswick so i can only get 91 premium at the pump, I'll just compensate with some octane booster. Thanks for info

Hey there guys was just wondering if i can get some info on if i should be mixing with race fuel, I have a 421 with 24cc domes at sea level, compression check showed 150 psi each cylinder, I'll be running 91 octane pump fuel, any info would be great ! thanks

Was wondering if i could get some information on what jetting to run with the 485 cheetah at sea level + dome size ( 91 octane pump gas) would like to know what people are running to start with a good base , I have Keihn D-slide carbs.

i have stock cylinders with the vitos 404 big bore sleeve, with the long rod 4mill crank, Im running V-force Delta 2 reeds, with the pro design manifold system and boost bottle, and Fmf fatty exhaust