coldsmoke

Bought used with 170 jets, obviously way too big to even start with.

Stock shaved head, probably just under 11:1. No port work. Say 300 ft above sea level.

Oh yea, I'm in detroit michigan couple hundred feet above sea level.

Hey guys, hoping u guys could get me close enough to dial it in myself. 4 mil banshee, t5 pipes, kn pods. Runs on 93 octane. I ran 280s in my stock mikunis but as we all know the keihin follow a different number system. Thanks a lot!

I'm looking to buy a set if used pro peg bars. Whatcha got?

Length? IDK off the top of my head but its a +4 so whatever a stock banshee swinger is, plus 4 inches. It handles amazing tho, especially after riding my stock-armed raptor that never sets the front wheels down. Like is said tho, im going to use it. thats why im going through all this madness. Just bought a 40mm carrier for it actually.

I just bought a banshee with a complete 250r Rear end with banshee shock. Found out the hard way after ordering parts that it was an R rear end.... it IS possible.

Its a +4.... But no. i plan to use it on my build. Anyone hear of someone using a honda carrier im a yama swinger? I really hope its possible because i have a new 400ex carrier on the way!.... Im beginning to think that my swinger wont clamp down small enough to hold the carrier.... anyone looking for a brand new billet honda carrier? haha

So are the 250R and Banshee Carriers the same O.D? A 400ex should bolt into my swinger to allow me to use this axle if im doing my research right.

Nice... Its a 250R axle. A 250 carrier will fit in my swingarm for the swap right?

4 holes. its an aftermarket billet hub.

... and thanks for the bump and the specs slim!

Thanks, but i just purchased a set of 35mm Airstrikers from an HQ member. I plan on using these bowls because they look badass. 200 shipped for these carbs, Sorry, no intakes.

Swingarm pics http://i1181.photobucket.com/albums/x439/ax3883/012.jpg http://i1181.photobucket.com/albums/x439/ax3883/011.jpg http://i1181.photobucket.com/albums/x439/ax3883/010.jpg I have to retake the axle pics bc they were blurry. they seem to be set up the same, except the carrier has a larger internal diamter to fit the thicker axle. The hubs were very close to 4 1/2" on center when i eyed them up with the tire still on. the brake rotor was a smallier diameter than the stock banshee... about the same size as the rear sprocket. A larger diameter axle would make sense. Are the larger diameter carriers common?

I purchased a new 'shee with a +4 durablue axle on it. the guy told me that banshee wheels dont fit the back and thats all he knew. i figured someone had put honda hubs on it. i tried to swap my +4 banshee swinger to that quad and found that the new axle has different splines and a larger diameter in the center. It makes me think that the axle as well as the swingarm are from another brand? id like to use the axle/hubs because they fit the beadlocks that came with the bike so i guess im shopping for a +4 swingarm for a mystery machine with a larger diameter rear bearing. Any help you guys could lend is greatly appreciated! hint, it also came with a 2 piston rear caliper as my banshee brake only had one piston.

consider a trade for a nice set of the same carb but built for alcohol with power jet? if so, lemme know. would add cash for the filters too.

nice set of 34mm pj's with power jets, lines, built for alcohol. lookin for some good carbs for my 4 mil long rod with t-5s. thanks.

This things are priced to move! Theres nothing wrong with them, just want to sell them fast so i can pick up some gas carbs and get riding again ASAP.

Trade for some nice 34pj's with power jets. alky setup? I just need some gas carbs.

...and buy the pods and outers.

Trade for a nice set of 34 PJ's with billet bowls set up for ALKY?

I just picked up a set of 34mm pj's with the power jets installed for alcohol. Billet bowls. I have no plan on using them, but pretty much got the billet intake for free so i figured i'd sell the carbs and buy a set of 34mm gas carbs to replace them. Theyre in nice shape. $225+shipping or possible trade for a nice set of 34mm gas carbs.