istoleacamaro

pm me a price on the nerf bars if you would and if you can send me a picture to [email protected]

pm'd

dang jeff come on now i asked you about that bumper last time i was up there!! lol its cool just give me a call sometime this week and try to get me a picture of the stuff if you are able to

pm me price on clamps

give me a call im pming you my number i want the carb tops and the cable if its not gone to make my bike loose tors!

can i get a crossover tube and one or both of those kill switches??? got a key and key switch??? (i have the bracket)... pm me price + shipping please kansas 66614

how much is shipping for a set ne ways? im in topeka ks 66614 and might take a set for cheap enough

dibs on the tank and rad cover, please email me pics to [email protected] and if you could send me a PM saying you did so i dont check email very often... thanks

Ok so tomorrow im getting a new axle to finish my banshee up and i also bent the sprocket and hub while getting the hub off the damn axle... so what im wondering is can i take the sprocket and hub off of my parts blaster and put it on my shee?????

im in KS and im running 300 mains with those mods and i dont think its quite rich enough yet... going to 310s or 320s

if you do attempt it id put a big tranny cooler on it and change out to some really good ATF... but thats just my opinion....

Jeff is an awesome guy, he helped me get my shee back together and always has all the stuff you need... He thankfully stocks a lot of stuff... Most of it is genuine stuff too!

OK well i jimmy rigged the hell out of my TORS boxs and actually broke the idle screw off of the other one and took out all of the mechanics... it doesnt idle but it still runs and pulls at the same time... i still need a kit tho but im happy, it runs!

have determined i need either a TORS box or a TORS removal kit

Ok ive hauled ass all weeekend to finish my banshee for a little riding before winter. i did a case up motor rebuild and tons of other little things, went to put the TORS on the carbs and its missing the idle screw on one carb does anyone from topeka or the areas around it such as holton or whatever have a TORS box, or a idle screw or a TORS removal kit even? call me my names zack 785-806-9845 and im ready to go get it

new plugs, fog it with starting fluid and start towin it down the street...

600 for the whole bike and mods

got it apart, got it to jeffs and one of the bearings fell apart, it ate a few orings, and the reason it shifted to begin with is because they used a piston ring for the retaining clip.... it ate up the seals and a whole buncha stuff so its gonna get all new goodies from the ground up... now i pray it just holds together

will the nerfs fit a shee? not sure

well i kept going despite my fear and got the big parts off and split the cases... magically half of the bottom bolts were finger tight and as soon as i broke the torque on the other nuts the crank just so happened to fall back into place.... but i did find o rings all ripped up on the crank ... oh well off to jeffs tommorrow to get his oppinion and buy some parts!

make sure the jets are appropriate for your atmosphere and mods... 2 strokes jetting is WAY more critical than a 4 strokes... since the oil is in the gas... use a GOOD oil not some walmart special... i always reccomend redline racing synthetic... i love the stuff

785-806-9845

Yeah hes been very helpful so far but he just physically cant be there to answer all of my questions, a lot of them have to be seen to be answered.

So i bought a banshee that was blown up, melted a piston. Started to disassemble it and had the cylinders bored 30 over and bought pistons from jeff and got gaskets and all of that stuff. I was going to reasemble it this weekend and took it to jeffs and one of his employees noticed that my crank was purple and that it was rubbing on the cases. I guess it shifted over. So i say great and buy a clymers manual and attempt to disassemble it myself. Upon disassembly i notice the waterpump gear is melted and just kept going. I think im in way over my head and just want someone who will help guide me through the process... The book really doesnt do much for me. I dont know why. If anyone will please PM me.

would also loev some kinda of wheel spacers