huskyohilux Posted November 5, 2007 Report Posted November 5, 2007 Have assembled my rear axle and was just about to throw away the old parts when I found this spacer. It goes either between the posi-lock and the sprocket hub or between the sprocket hub and the carrier. That's what I disassmabled when I replaced bearings, seals and chain sprocket. Please help me out, I haven't ridden the bike yet but everything feels good enough... Quote
xXBlessedWithDeathXx Posted November 6, 2007 Report Posted November 6, 2007 when you replaced the bearings did it come in pieces? that looks like the race that the ballbearings sit in. Quote
CFM Posted November 6, 2007 Report Posted November 6, 2007 http://www.powersportspro.com/pages/parts/.../2/default.aspx check it out... Quote
xXBlessedWithDeathXx Posted November 6, 2007 Report Posted November 6, 2007 (edited) http://www.powersportspro.com/pages/parts/.../2/default.aspx check it out... that link didnt open to a page for me but i think this is what you wanted to show. 1 Collar, Wheel (superceed: 5TG-25383-00-00) 2 $58.36 ea Add to Cart 2 Rear Wheel Comp. Deep Violet Solid 1 (Backordered) 2 $371.91 ea Add to Cart 3 Tire (At20x10-9**Kt877 T/L) Dunlop 2 $88.15 ea Add to Cart 4 Valve, Rim 2 $6.60 ea Add to Cart 5 Nut, Flange (superceed: 95704-10500-00) 8 $1.06 ea Add to Cart 6 Washer (superceed: 92990-10200-00) 8 $0.49 ea Add to Cart 7 Washer, Plate 2 -- 8 Nut, Castle 2 $4.26 ea Add to Cart 9 Pin, Cotter (superceed: 91490-30030-00) 2 $1.22 ea Add to Cart 10 Axle, Wheel 1 $345.96 ea Add to Cart 11 Collar, Sprocket Axle 1 $70.21 ea Add to Cart 12 Bolt, Stud 6 $1.22 ea Add to Cart 13 Sprocket, Driven (41t) (superceed: 2XJ-25441-21-00) 1 $26.77 ea Add to Cart 14 Washer 3 $1.35 ea Add to Cart 15 Nut 6 $0.99 ea Add to Cart 16 Hub, Rear Silver (superceed: 3GG-25311-01-P1) 1 $173.14 ea Add to Cart 17 Spacer 1 $9.03 ea Add to Cart 18 Bearing 2 $19.65 ea Add to Cart 19 Oil Seal 1 $5.11 ea Add to Cart 20 Oil Seal 1 $5.11 ea Add to Cart 21 Puller, Chain 1 2 $12.28 ea Add to Cart 22 Bolt (superceed: 90101-08777-00) 2 $1.16 ea Add to Cart 23 Nut 2 $1.14 ea Add to Cart 24 Chain (D.I.D 520v6 104ll) (superceed: 9Y581-08103-00) 1 $145.34 ea Add to Cart 25 Joint, Chain (D.I.D 520v6-Fj) (superceed: 94681-87011-00) 1 $4.89 ea Add to Cart 26 Bolt 1 $3.13 ea Add to Cart 27 Washer, Plate 2 $0.49 ea Add to Cart 28 Bolt 1 $9.38 ea Add to Cart 29 Washer, Plate 2 $1.31 ea Add to Cart 30 Nut (superceed: 95704-10500-00) 1 $2.20 ea Add to Cart 31 Nut 1 $1.87 ea Add to Cart Edited November 6, 2007 by xXBlessedWithDeathXx Quote
huskyohilux Posted November 6, 2007 Author Report Posted November 6, 2007 when you replaced the bearings did it come in pieces? that looks like the race that the ballbearings sit in. Should have said that I have the roll design swing arm with housing for tapered bearings. So unfourtunatly the picture didn't help me much. And since I have only one of these unidentified washer I don't think they come of the bearings. In fact I'm pretty sure I didn't see it there when I removed everything. Must have come from either the posi lock or sprocket hub. Quote
4stroker Posted November 6, 2007 Report Posted November 6, 2007 i think you get that washer with your axle when you buy it and you use it if installing that axle into a blaster dont take my word for it though!! Quote
huskyohilux Posted November 6, 2007 Author Report Posted November 6, 2007 i think you get that washer with your axle when you buy it and you use it if installing that axle into a blaster dont take my word for it though!! I took a closer look at my old posi-lock (I had to cut in half to remove it) and there were markings on the inside towards the sprocket hub. Obviously thats were it used to be. I'm not sure if I need it though...It doesn't affect anything but the positioning of the nut. The threads are exposed as pictured, is that a problem or am I good to go??? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.