tdod101 Posted December 19, 2013 Report Share Posted December 19, 2013 I have the urge to build a badass motor from the ground up, I wanna keep using the one I have so I can still ride. I wanna buy all the parts I need from HQ members, Basically start off with the cases clean them up and figure out what I wanna do with it. What do you guys think ? Which direction should I go. I'm in no rush so I can definitely take my time, also I would like to stay on pump gas but IF I have to buy VP race fuel I suppose I can Quote Link to comment Share on other sites More sharing options...
lms1977 Posted December 19, 2013 Report Share Posted December 19, 2013 with out a budget or expectations out of the motor its hard to give you advise.. some people would think 60hp is badass while the next will say 130hp is badass so we would need more info Quote Link to comment Share on other sites More sharing options...
tdod101 Posted December 19, 2013 Author Report Share Posted December 19, 2013 i say extend your frame a couple feet and put a rotax 583 in it. BADASS No thx lol Well I can spend money over time, I would say I want to spend around $2000 - $3500 over time just on the motor. As for expectations I don't know, you tell me. The faster the better I suppose Quote Link to comment Share on other sites More sharing options...
sheerider11 Posted December 19, 2013 Report Share Posted December 19, 2013 Well your being very vague. 2-3k can go in a few purchases on a bigger motor. I think I have about 2k into my stock cylinder 4 mil. That paid for crank port all hardware domes assembly install tune and whatever else is involved with that Quote Link to comment Share on other sites More sharing options...
sprinklerman Posted December 19, 2013 Report Share Posted December 19, 2013 For 2-3500.00 you're looking at a good 4mm CP cylinder engine. Serval or cub. That's assuming you are using all good quality parts. Quote Link to comment Share on other sites More sharing options...
tdod101 Posted December 19, 2013 Author Report Share Posted December 19, 2013 (edited) Hmmm, I'm kind of leaning towards a cub motor Edited December 19, 2013 by tdod101 Quote Link to comment Share on other sites More sharing options...
tdod101 Posted December 19, 2013 Author Report Share Posted December 19, 2013 Like ? Quote Link to comment Share on other sites More sharing options...
dirtydownunder Posted December 19, 2013 Report Share Posted December 19, 2013 800 cylinder + possible 350 for porting 450-500 crank with bearings 200 for case 400-600 modded trans with new bearings 300-400 for clutch setup 350 for pistons n gaskets. plugs n extenders 280-300 for cool head and custom domes 500-700 for pipes. 350 for carbs. 500 for just in case. 1 Quote Link to comment Share on other sites More sharing options...
Sandking Posted December 19, 2013 Report Share Posted December 19, 2013 Amazing how it'll nickle and dime ya. Sent from my SCH-I535 using Tapatalk Quote Link to comment Share on other sites More sharing options...
tdod101 Posted December 20, 2013 Author Report Share Posted December 20, 2013 So more like 5 g's Quote Link to comment Share on other sites More sharing options...
2004LEBanshee Posted December 20, 2013 Report Share Posted December 20, 2013 Should have no prob staying around 3500 for a 4cub or serval. Do it right talk to a good builder and buy from them. They will usually give you a little deal on stuff if you buy enough. Imo Quote Link to comment Share on other sites More sharing options...
sheerider11 Posted December 20, 2013 Report Share Posted December 20, 2013 So more like 5 g'sYes. That'll get you what you want with out settling when you start coming up to your max. So if you want this for 600 but your 1k away from you budget and your only half way done, you won't settle for the 300 one that's half as good. So 5 is a good budget with a lot of cushion room. Quote Link to comment Share on other sites More sharing options...
B.b.p builders Posted December 20, 2013 Report Share Posted December 20, 2013 I think you could build a good motor for like 2500-3000, look for deals don't buy new, buy most parts in good used condition. Quote Link to comment Share on other sites More sharing options...
B.b.p builders Posted December 20, 2013 Report Share Posted December 20, 2013 Most sell 421 cub kits complete with crank and porting for like 1700-1900$ I will sell you a good set of cases with tranny for cheap, good base to start with. Quote Link to comment Share on other sites More sharing options...
tdod101 Posted December 21, 2013 Author Report Share Posted December 21, 2013 (edited) Thanks bbp Edited December 21, 2013 by tdod101 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.