Jump to content

bansheerabbit

Members
 View Profile  See their activity

  • Posts

    26

  • Joined

  • Last visited

 Content Type 

Posts posted by bansheerabbit

  2. What size jets for new carbs that have arrived

    in Jetting & Exhaust Forum

    Posted

    G'Day all

     

    I have just received a set 32mm Mikuni round slide carbs and wondering what size get would be a good starting point

     

    2006 Banshee

    CPI Inframe pipes

    drag ported

    Stock 64mm bore

    +4 Timing

    VForce 3 reeds

    Coolhead 19cc Domes

    98 or 100 octane pump gas 32:1 Castrol TTS oil

    Air filter - ProDesign foam filter and foam outer (oiled) mounted to stock air box and modified lid half open

    Elevation 200 feet

    Temp range 60-80f

     

     

    Thanks for yur help inadvance

     

    Carbs came with 200main jet and 35 pilot

     

  7. Wiring harness/loom

    in Wanted

    Posted

    Chasing a 2003+ wiring harness/loom complete (Square Plug) need everything i.e coil, regulator etc etc I have both STD and a DYNA FS CDI  to suit 2006 shee but if you only want to sell complete I would still be interested

  9. Wirring harness/loom

    in Wanted

    Posted

    Hi Guys I'm chasing a year 2003+ wiring harness I need everything ie, coil, reg, plug leads etc etc DONT NEED black box(have a Dyna FS) also chasing a thumb throttle (dont need card cables) Thanks in advance

     

    Downside location AUSTRALIA - I have had pleanty shee parts shipped b4 and freight not to bad. Deariest thing would have been $150us shipping cost for full set fullbore plastics , CPI pipes came in at $80us frieght. Al items here in under 1week

     

    Cheers

    Rabbit

     

     

  10. Help needed in bike set up

    in Drag Forum

    Posted

    Hi All,

     

    I am in the process of setting up my 07 banshee as a asphalt drag shee.

     

    I have no started the engine since full rebuild - 64mm pistons (wisco) ported cyclinders, std stroke Hot rods crank, lockup clutch (rest in signature)

     

    I have Nitrous and would like to run on alky. 39mm PWK carbies (use bike between 0-600 feet) temp 65-80

     

    What size jetting should i use for the above set up? What alky oil ratio?

     

    Also on cars you need to enlarge ring gap when running alky and nitrous is it the same with banshee's?

     

    Also any other info on how to set bike up would be greatly appreciated i.e suspension etc etc. Have state titles in 4 weeks so i would to go out and kick some butt!

     

    Thak you very much

     

    Cheers

    Rabbit

  11. Got my 07 Banshee today

    in General Banshee Discussion

    Posted

    Hi all,

     

    Been waiting 2 weeks now for my new Banshee to arrive, finally got here today.

     

    I ordered heaps of parts for it the day I ordered bike. CHECK out sig for some the items being fitting tomorrow to bike. As you will notice I have another couple shee's in stock. You can never have enough can you?

     

    I will port, weld crank etc later guy's. Did last port job my self, bike runs great heaps more all over.

     

    Anyway happy and safe riding.

     

    Rabbit

  13. Banshee Smokers

    in Roostin' Room

    Posted

    I smoke both!!!! Perfer to have my daily green intake!!!!!

     

    Best thing happened last weekend I was outside having a joint and the sexy bird from next door stuck her head over the fence and asked for some. Needless to say I invited her in and we had a session from hell. I could hardly move by the time she left. I see her every night now for smoke still trying to get in her pants proberly tonight or tomorow depends on how stoned/pissed we get!!!!!.

     

     

     

    Skunk, Super Skunk, Bubble Gum, Northern Lights, Four Seasons are some of the better buds we are producing now and years gone by so whats happening in the rest of the world.

     

    RABBIT

  16. Wiseco Piston Problem?

    in Banshee Repairs and Mods

    Posted

    Thanks for replies guys.

     

    I found the locating pin lst night deep inside top of left piston. Order today a new wiseco piston kit. I have another std head but I have a coolhead on ordered so will just tidy up damaged head for now - only has about 20 marks from pin in it.

     

    I was looking at my 100thou over RZ piston kit last night from wiseco and noticed that one of the locating pins was a bit lose, before I install the new pistons I will loctite the pin in place or should I return to place of purchase?

     

    The only time I have had wiseco's break at skirt near window is when I have opening windows up a lot more than I should have.

     

    Rabbit

  17. Wiseco Piston Problem?

    in Banshee Repairs and Mods

    Posted

    Hi All,

     

    I pulled banshee apart this weekend due to lose of compression. 130 right and 125 left with 20thou off head should be around 150 I think.

     

    I thought I had broken a ring, the problem is that the left piston the pin that locates the lower ring fell out and made a mess of head and piston but didnot leave a single mark on cyclinders still see hone marks from 6 months ago (new wiseco pistons installed at same time).

     

    I have just ordered a new set of rings and will be back together shortly I plan on just filing top of piston flat again and diegrinding head.

     

    Has anyone else had this happen???

     

    Rabbit

  18. Replace Flywheel Only ?

    in Banshee Repairs and Mods

    Posted

    Hi Hasty,

     

    Do yo have the rest of the RZ Engine? If so convert bike to RZ power might be cheaper than getting a flywheel shipped in. If you do get one shipped get a lightened one you wont be disapointed. Taken 250grams of std banshee flywheel and 220 of RZ flywheel amde a big difference to bike reving up quicker

     

    Rabbit

  19. ?light System (christmas Tree System)?

    in Drag Forum

    Posted

    Hey everyone,

     

    I am just trying to get things started in my area and was wondering the same as THE WOLF about the chrissy tree light/timing system!!

     

    or does someone on here have a plan on how to make them.

     

    Be good if I could find a 12 volt system otherwise will have run an inverter.

     

    Rabbit

  20. Anyone Have Raptor Starter Problems?

    in General Banshee Discussion

    Posted

    My Craptor is giving me the shits!!!!!!!!!!!!!

     

    I am having electrical problems from starter motor to cdi. I've had it at 2 auto electricians and they can not locate the break in wiring harness. The bike just stops as you are riding it. All connections are clean etc but there is something not right. Died on me again on sunday. Just as well I took my banshee along also!!!!!!

     

    LONG LIVE THE BANSHEE

     

     

    Rabbit

  22. Rz350 Tranny

    in Drag Forum

    Posted

    I am going to use my RZ tranny in my RZ Shee. I will let you know in about a month or 2 on how it preforms. Just got last engine peice last week so time to put together.

     

    I will be using the RZ-Shee for mainly drags so the longer legs should help.

     

    Rabbit

  25. RZ or Banshee Transmission ??

    in Banshee Repairs and Mods

    Posted

    Hi Meat,

     

    You would find that the RZ Tranny would be quit a bit taller than the banshee. Have looked at it a couple of times and worked out that I would need to install a larger rear sprocket (not available - have to adapt one) as a friend has tried it and found that he has to slip clutch a lot to get of the line but once moving not a problem just missing holeshot.

     

    I still have my RZ bike in use on the road. I am fine tuning the performance side of thing first before installing in Banshee. I will proberly use the banshee tranny. My engine casein banshee is already a RZ one with all the banshee bits inside (mate smashed bike and destroyed engine case)

     

    Rabbit

BHQ Quick Links

×
×
  • Create New...