sheeBnasty

No one needs some pipes..

The T5 Header pipes are also for sale...$200.00 shipped OBO.. Would sell the Stage IV setup as well..

Thats cool..I told him I would but never heard back from him..so they are still for sale or trade.. I need some carbs.. sorry for the confusion..

My Bad..I figured everyone would read the first post...$200.00 shipped OBO..reasonalble offers that is..

make offers...

You need an Ohm meter and test everything you can...here is a link that will help you.. http://www.dfn.com/benkaren/elecfaq.html Scroll down on the pape and it tells you how to test everything for resistance, that will help you eliminate problems..one of the tests is wrong though, Secondary Sideo of the Coil, to check the plug wires/caps put one of the Ohm meter leads in one cap and the other Ohm meter lead in the other and you should get some resistance. The only piece you cannot really test is the CDI box because it is a solid state circuit but you should be able to test everything else. I just went through this same issue, mine was the CDI which I know is rare..but that link helped me out..would of been lost with out it... Does your shee still have TORS? Has the Key Switch been bypassed, have you made any recent mods or changes? Hope this helps..

I need a set of carbs, intake, and filters for my shee...would like to get 30mm or larger..I have a set of T5 header pipes to trade.. http://www.flickr.com/photos/26084450@N03/3017675051 I aslo I have Trinity Stage IV 2 into 1 setup with a new intake boot, 35mm PWK and K&N that I would be willing to trade for a dual carb setup.. Or..would consider trade for another 35mm PWK and intake...and keep my 35mm PWK and filter. What you guys got.......

ttt

Have a set of T5 header pipes that have some rust near cylinders and one of the hanger tabs have been welded but look pretty good when mounted w/ plastics on..$200.00 shipped OBO... http://www.flickr.com/photos/26084450@N03/?saved=1

Paul Turner Pipes Sold..

I am looking for a 4mm crank and a Cool Head..would like a Noss Head...

$200.00 OBO on the Paul Turner... Don't have a clue on the LRD's...make offer or if you got something you want to trade let me know....

I have a set of Paul Turner Mid Range pipes with Fat Boy Silencers. The pipes were black but they need a fresh coat of paint.. http://www.flickr.com/photos/26084450@N03/3007064846/ I also have some chrome LRD header pipes no silencers.. http://www.flickr.com/photos/26084450@N03/3007064260/ PM me offers.. also would consider any performance parts for my Shee..

I am looking for a good place to have my jugs ported and polished... I live in the Dallas/Ft. Worth area of Texas. Is there anyone around here that does good work or am I going to have to send them off. I am looking for a Dune Port and Polish.. Thanks guys..

Cool guys.. Thanks... Looks like I am going to go with a Noss Head.. Now should I go with 17cc or 18cc domes? I am going to have a dune port and polish job done on my jugs..

When you say you have no resistance on the coil with an ohm meter, what all did you test? You should have resistance between the positive and negative plugs on the coil and between the two plug caps. If you tested from the negative side of the coil to one of the caps and got no reading that is fine...that test is wrong...I bought a new coil because of that and it ended up being my CDI, which I know is very rare. But my bike was a bitch to start before and then I had no spark. Ohmed out everything, replaced the coil because of bad testing instructions...made sure all my splices and switches were working correctly, tested my stator, pickup coil, pickup coil gap - very important that is right.. Then put the new CDI on started first kick.. see if you can find a buddy with the same CDI and swap them out to eliminate CDI...

So I had a Pro Design Cool Head with 17cc domes on my last shee, but now there is few other options when it comes to Cool Heads besides Pro Design..like Trinity, Chariot, Mod Quad, Fire Ball, HTR, RDZ etc....is there one better than the other? Sorry if this has been covered before but I could find any post about it.. I am building my Shee just for the dunes.. a lot of dune riding and jumping, but also like to hold my own when dragging...so any suggestions would be greatly appreciated...thanks guys..

Is there somewhere else I can get a new intake boot for my Stage IV 2 into 1 setup besides Trinity Racing? Just curious. Thanks guys..

I don't have the silencers that go with them..sorry guys I know this is a shot in the dark..the guy gave them to me when I traded for the Shee..I have looked them all over and there is nothing on them at all..

Still haven't figured out what kind of pipes those are...I put them on the other night and you would have to cut the stock front fenders for these pipes to even fit.. Just thought I would throw that out there to see if that might help. Just would like to know what they are..thanks again guys for any help..

Thanks for all the responses guys...got me a pair of T5's...thinks again for everyone's help..

I am looking for some chrome T5's (headers and silencers) for my 95 Shee. Send me a PM with price shipped to Midlothian, TX 76065.. Thanks everyone..

I got these pipes with the banshee I just bought to fix up. I just don't know what kind they are...can someone help me out and tell me what kind of pipes these may be..there is no markings of any kind on the pipes.. http://www.flickr.com/photos/26084450@N03/...in/photostream/ http://www.flickr.com/photos/26084450@N03/...in/photostream/ Thanks for any help..

Where is a good place to put my banshee up for sale? Don't get to ride hardley anymore. Think I am going to get a street bike. If anyone is interested it is a 99 shee, .20 over, wiseco prolites, cool head, 17 cc domes, some port work, twist throttle, pro design intake - no boost bottle, K & N, Toomey T5's, and a powder coated frame. Here is a pic of it.