BANSHEERSA

A guy came to buy my Shee and test rode it and top end wentout . So can somone give me a list of everything i will neeed to order? Jugs are fine no scratches in them . And im gonna go ahead a split cases while i got it this far so another list of what i will ne3d to order for that to thx ! Sent from my SM-G900P using Tapatalk

Diggin the Purple !!! Sent from my SM-G900P using Tapatalk

Ok so now how n the world do i adjust it?? Iys all together but when i hit 1st it pulls nut not enough? Kinda like it is still engaged Fuck you tube them assholes dnt tell u the specifics! !!! Sent from my SM-G900P using Tapatalk

I need heLP I am nt sure how this goes bac together?? Got clutches on Washer nut tighten 58 flbs Rod Ball Now is it the pancake? Or basket cover? Sent from my SM-G900P using Tapatalk

Hit me up what u want for the swingarm 678 615 9166 Sent from my SM-G900P using Tapatalk

Well thats what i was thinking so i called him and he is coming over to look at it for me he says i must have did something to make it run like this So he said hes gonna get it bac right for me and send me bac to the track and said if i lose then hes gonna come bac with me the nex week and he is gonna run it so we will c ill hit bac after this fri Sent from my SM-G900P using Tapatalk

And do u know bout sprockets? Trying to figure what tooth count was thinking 16 or 17 Sent from my SM-G900P using Tapatalk

So on the clutch side right Sent from my SM-G900P using Tapatalk

What tooth count should i b running? I Drag got Vita's Pipes,heads vforce 3 reeds, on 18x10 slicks and got it lowered i am topping out at 78 but the guy i bought it from says it will do 104 n an 1/8 so i am new at this so it might b me... Sent from my SM-G900P using Tapatalk

So i have the pancake barring now so hows it go on? Actuator pushrod ( and isnt the push rod supposed to be longer??) Then the pancake right Sent from my SM-G900P using Tapatalk

Jus had this happen 2 weeks ago and fixed it Now it happened again but this time ì can't get the actuator out or the push rod ?? I have the pancake barring to put in this time? But how come it did it again? And how do i get the rod out? Sent from my SM-G900P using Tapatalk

I jus weilded my clutch actuator to the pushrod. But fixed it... Now 2 weeks later samething.... Whats going on with it ? Im nt riding the clutch to cuz it. And this time i cnt get the rod /ball to slide out Ihave the pancake barring to put bac n plz help Sent from my SM-G900P using Tapatalk

Sweet where u located? Im n Douglasville Ga im prob gonna need the stuff to fix it i would like to make it to the track on fri nite my / 678 615 9166 Sent from my SM-G900P using Tapatalk

Thx man Sent from my SM-G900P using Tapatalk

Ok so what do i need to do? Im nt a mech but i have common sense but tell me if im on the right track. So i need to take the clutch cover off and check c if there is any debris nside if nt jus pull out the acc. And replace it? Am i on the track? If nt plz help me Sent from my SM-G900P using Tapatalk

I was drag racing and when i crossed the finish line and pulled on the clutch it mad3 a pop and the clutch cable felt loose now i c the clutch actuator is bent so i straighten it and put cable bsc on but it wont pull out of the motor it jus bends ??? Sent from my SM-G900P using Tapatalk