r/atvshee
-
Posts
1,164 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by r/atvshee
-
-
No, spindle mounts are sold
-
1
-
-
Phoenix, Az
-
Swingarm, water pump cover and clutch lever are SOLDSOLDSOLD
-
Clutch basket, impeller, brake pedal, gear slammer, brake cap, block off, dip stick, stator cover, kicker, front shaws, throttle assy are SOLDSOLDSOLD
Shearers and axle are SALE PENDING
-
Crank, flywheel, timing plate and IGN coil are SOLD
-
Inbox cleared and PM's replied
-
Well, I am completely parting out my 421 Cub. I built it in late 2012-ish, broke in the engine, went to Glamis once then parked it for roughly 2.5 years. Life happened, just havent had the time to go riding and have gone into the deep end of track days and slippery slope of constantly throwing money at my car for better lap times. The bike sat out side, and certain parts show damage from sun and weather (rust) and have been priced accordingly. All prices are OBO, buyer pays shipping. Small parts that I have F/S, will be let go for the cost of shipping as indicated.
Since there is alot of stuff F/S, I will send more detailed pictures upon buyers request.
Engine - From what I remember, the engine ran flawless the last time I rode it 2+ years ago. A few weeks ago the bike would not turn over. A few days ago there was a lot of liquid in the right pipe. The cylinders will need replating due to the damage on the right cylinder. Rod bearings feel fine as well as the crank bearings. The top case has slight chain wack, but nothing major. Transmission operated as it should.
1-5 N down Dunable Override - 250
Crank Cases - 100
39mm Carbs setup for GAS w/ filters - 250
39mm billet manifold - 75
vf3 reeds - 125Chassis parts - Frame is PC'd Trans Purple and lightened w/ bolt on subframe by Tim at Stellar. Bought the frame from Tim back in '09 and has not been wrecked. There is a spot of PC missing in the front of the frame. Frame is straight and titled, I would prefer local pickup but can ship at buyers expense via grey hound. The J-arms will need ALL ball joints replaced. The Direct Drive spindle mounts will need bearings replaced and need new valve stems. The tires are old, but dont show dry rotting and hold air. The swingarm has a crack behind linkage mounting point and discounted accordingly since it will need to be repaired, or will end up in the trash if nobody wants it.
Lightened frame w/ subframe and title; Frame is straight, a small area of pc missing in the front. I would prefer local pickup but can ship at buyers expense via grey hound- 500
Marvin Shaw13.5” rear Coilover - 175
Chrome Steering stem - 75
renthal handle bars - 40
chrome footpegs; rusted in certain areas - 50
polished linkage - 50
Sold list-
4mm crank
Billet clutch basket
lightened flywheel
timing plate
IGN coil
Stator Cover
Billet Dipstick
Marvin Shaw Front Hillshooters
Stellar J-arms
Brake pedal
Gear Slammer
+8 LSR swingarm
Billet rear brake cap
Parking brake block off
Water pump cover
Clutch lever
Kick starter
Chrome throttle assy
Spindle mounts
Rear Brake line
Shearer inframes
JJ&A Axle
421 cub cyl
chariot head w/ domes
Direct Drive lockout w/ clutch cover
Due to the holidays, I will not be able to ship as immediate as I have in the past.
-
Sorry. Someone was ahead of you.
-
Paddles and pegs are SOLD
-
22x11x8 14 paddle extreme 72" RO - 410 shipped.
Still in very good condition. No leaks or dry rotting.
Cascade chrome "race position" foot peg and billet shifter. 120 shipped
Chrome is still in good condition. Due to the foot pegs having a different position than stock, I will not separate shifter from pegs.
Also, I wouldnt recommend these for any one that rides in decent sized whoops, unless you dont mind digging your feet through the sand.
Will also trade for chrome stock pegs or billet pegs with billet or chrome shifter.
-
Domes are sold!
Open to offers on both rear Shaws!
-
Paddles are sold!
I'm open to offers on everything else
-
13.5" Rear Marvin Shaw Hill Shooter - $180 shipped
No leaks, setup for a +12 swingarm with linkage
13.5" Marvin Shaw Rear Competition - $150 shipped
No leaks, setup for +6 Swingarm with linkage
-
1
-
-
Sale pending on it. Will let you know if anything happens if your still interested.
-
Funny you say that if some one has a 10cub thats beaten up, you're ready to buy. But when you bought a 10 cub with a piston with slight deto, you start all this drama.
If your willing to pay money for ANOTHER cub topend, shell out the 25$ for a planetsand membership. You might have better luck there if they arent informed about all your shenanigans.
-
-
Daj is right. Youll want a cut trans. We had a hard time shifting at full power in this setup without an override. It wasn't as bad as a 4mm cub but still not very fun. You should try not to skip that while the motor is already apart.
-
What kind of porting is done?
How's the plating?
If you decide to part it out, I'd take the cylinders.
-
Stock stroke cub sold
-
-
thumb throttle sold.
-
Pics are working for me. The color is silver.
Water pump cover sold
-
Direct Drive lockup and polished cover 200 shipped
13.5" Rear Hillshooter 185 shipped
No nicks, dings, dents or leaks. Setup for a +12 swingarm
13.5' Rear Competition 150 shipped
No nicks, dings, dents or leaks. Setup for a +6 swingarm
Chrome rear grab bar 25 shipped
Not bent. Chrome is still in good condition.
Clutch perch and lever 20 shipped
Eliminates parking brake. Not bent.
Mod quad exhaust hangers. 15 shipped
No bolts, just spacers. Could use some polishing.
Cascade Tail light cover 15 shipped
Open To offers.
Still looking for unported 4mm cub cylinders.
-
Prices dropped again...
Need this stuff gone, make offers.
421 Cub complete part out
in For Sale - Parts & Accessories
Posted
Yes I still have it.