Jump to content

Stinger

Members
 View Profile  See their activity

  • Posts

    281

  • Joined

  • Last visited

 Content Type 

Posts posted by Stinger

  2. small coolant hose routing?

    in Banshee Repairs and Mods

    Posted

    Any one have a diagram of the small coolant hose routing. Im in the finishing stages of my complete frame up rebuild and need some advice. I have the top coolant overflow reservoir hose connected to top of radiator (left side) lower reservoir hose is not connected to anything. . 1 hose with a T connector? 3 hoses in need of routing. Any help with propper routing would be appreciated!!

     

    They are crankcase vent hoses, not coolant hoses. They vent from under the water pump cover, between the cylinders, and at the back of the engine near the rear shock. The "T" ends up on the front right side of the engine.

  5. F.A.S.T Clutch Lock Nut/Pancake Bearing Questions...

    in Banshee Repairs and Mods

    Posted

    I got a rattle under the clutch cover late last year so I parked the Banshee until I had time to mess with it. The rattle seemed to only be at idle in neutral but maybe it's just because the Shee is too loud otherwise. If I remember right, pulling in the clutch lever made it quit. So it's getting warm and time to fix it.

     

    Pulled the cover off, at first didn't see anything that looked odd. Then I noticed the nut in the center of the clutch wasn't touching the clutch plate (the front plate that the springs are on). There is nearly a 1/4" gap. In the picture I attached (an old pic of when I installed the clutch a few years ago) you can see on the left the pancake bearing and the nut and threaded section on the end. See how the threads are sticking through the nut a 1/4" or so? Well when I pulled the cover the nut is hanging off the end by about 1.5 threads. The weird thing is the nut is tight on the threads and won't freely spin.

     

    So my assumption is I need to loosen the nut, thread it on farther so it touches the clutch plate again, etc.

     

    My questions are, am I correct in my assumption? What keeps the nut from backing off? Do you preload the nut against the plate any? How do you know how far to thread it on? Thanks.

    post-16940-1238794260_thumb.jpg

  6. How To Install YFZ450 Shocks On Your Banshee...

    in Suspension

    Posted

    For those of you that say they are too stiff and the compression/rebound adjustments don't make them soft enough, loosen the spring nuts and run them all the way to the top (remove the preload). This will make them softer than stock if the compression is also set all the way soft. I'm only 140lbs and I can get them softer than stock or harder than stock using the three adjustments (preload, compression, rebound).

  8. Which Paddles to Buy?

    in Sand Forum

    Posted

    Dune Runners may be just the worst straight paddles there are. Whats done to your bike, and what is the fearing you want to run?

     

    Mods are in my sig...plan to add CPI's and a bit more compression to the list. Stock gearing or maybe go 1 tooth less on the front sprocket by next spring.

  9. Which Paddles to Buy?

    in Sand Forum

    Posted

    I think 10 paddle will be too much.

    a set of 21X10X8 10 paddle haulers on blue label.

     

    Since you said 10 paddles would be too much, I assume you miss-typed in the 21x10x8 10 paddle in the next sentence. Did you meant 9 paddle or 8 paddle? Thanks.

  10. Which Paddles to Buy?

    in Sand Forum

    Posted

    OK, I am having a HELL of a time finding any USED 22" tall 10" rim haulers with 8 or 9 paddles...so I'm thinking of buying a different size.

     

    I'm looking at:

     

    20-10-10 8 paddle extreme

    20-10-10 9 paddle hauler

    20-10-10 10 paddle hauler

     

    Which of these would best go with a 145lb rider, stock swinger, and 55-65hp engine with stock gearing?

     

    OR I'm considering going to an 8" wheel setup. My only problem with this is I probably do 70% duning and 30% dragging so it seems the 10" is more suited for my purposes. If I end up with 8" rims, should I go for a shorter paddle to help them dune better like 20's or so? 20x11x8 or 21x11x8 for example?

  18. Which Paddles to Buy?

    in Sand Forum

    Posted

    Sorry if I am blind, but what length swingarm? I run a full drag port(between 80 - 85 horse), 6 in swinger, and 22X11X8 9 paddle haulers buffed bead to bead(b2b). I hook hard, I am skyward every launch, can usually catch third before front wheels touch.

     

    Stock length swingarm, I'm probably only 55-65 horse. My lack of skyward action with a stock swinger illustrates the problem with my paddles. I'm sure not being heavy enough to put any substantial weight over the tires doesn't help either.

  19. Which Paddles to Buy?

    in Sand Forum

    Posted · Edited by Stinger

    What tire psi are you running?

     

    I was originally running 3.5psi but the tires would spin on the bead and go flat. I had to run 5-6psi to keep them inflated...

     

    Jeff at FAST helped on the porting so it's a bit more than just a RL stage III port...if I had some CPI's it would really scream.

     

    So it looks like 8 Paddle Haulers, maybe 9 paddle if I plan to have new pipes by then...

     

    Looks like 21x12x8 and 20x10x8 and 22x11x8 were all suggested. I do more duning then dragging so I assume the 10" wheel would be better for me. Which height and width though?

     

    Who's got the best wheel and tire package deals price wise?

     

    Do you draggers typically dump the clutch or slip it off the line?

  20. Which Paddles to Buy?

    in Sand Forum

    Posted

    I've currently got some 8 paddle Dune Runner 22x11x10 tires and they used to work pretty good with my old engine setup. I just got back from Little Sahara and when dragging, I could not get out of the hole no matter what I did. If I just put it in 2nd and dumped the clutch with it pinned, it would just spin before finally grabbing (no wheelie) but everyone would be 2-3 bike lengths out on me by the time I got rolling. I could run down and pass most of the other quads but I'd run out of track with the "drag" bikes with extended swingers...though I'd be gaining. If they would stay in it, I'd pass them another 100-200 ft past the finish. So I've got the power to be pretty damn fast if I could hook up.

     

    I tried slipping the clutch off the line and it worked no better...bog or spin. Even just cruising around the dunes it doesn't pull wheelies unless I've got someone sitting on the back...

     

    With stock gearing these tires are actually too tall for the power I'm making because I can't pull 6th gear in the sand...just holds speed after the shift but I plan to gear it down before the next trip. I normally run 20" tires in the dirt and can pull them in 6th no problem (88-89mph according to the street bike beside me).

     

    One problem with getting traction is my weight of 145lbs...consider this when suggesting paddles.

     

    If you need more info let me know, engine info is in my sig and I attached a pic of my paddles.

     

    I'm going to buy new paddles in hopes of getting a better holeshot while still being able to cruise the dunes well. What brand/size/paddle count should I look into?

  21. pump gas and compression

    in Banshee Repairs and Mods

    Posted

    I am trying to remember what is the hightest copression that you can run on pump gas. I think 170 and below is ok for pump gas or is that pushing it. I tried searching but couldn't find anything on it.

     

    Depends on many things, most notably your altitude. I'm at 1600 feet and was borderline at 155psi and 91 octane.

BHQ Quick Links

×
×
  • Create New...