Banshee508
-
Posts
84 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by Banshee508
-
-
Its been a lil bit but thanks for all all the info guys what paddle tires in the rear would you run there just pondering on what ones i want to buy
-
Sent from my iPhone using Tapatalk -
Yes around the crank on flywheel side
-
I bought all Yamaha seals and when i turn it it leaks a little less
-
Yes the clutch side if fine but i can’t get the flywheel side to seal up just keeps leaking and crank seem fine an not worn
-
The first time i did this time i didnt
-
Hi i just put my top end back on and torqued it all up and did a leak test and the flywheel side crank seal is leaking took. It apart an re replaced that seal and its still leaking and crank dont seem like theres any wear. Any tips or something
thanks
-
Im getting ready to seal my cases back together and have a tube of yamabond 6b will that work or should i get yamabond 4
any insight will be appreciated thanks kevin
-
So if i do lightly clean it up an use it it wont cause issues later down the road like blow by in that spot
-
And i got it with my cylinders from being bored an they say that one was fitted to my cylinder so another one isnt
-
It is a little off in that spot but its not rough and can’t catch my finger nail on it.
but im just worried about reliability being a issue
-
I just received my new pistons in an one has a small mark at the top around the edge would this cause a issue or not thanks
Sent from my iPhone using Tapatalk
-
There is a chance the shifter shaft is stuck happened to me an the little spring got caught on it an only shifted into 1/2
-
I Just got it off an is this normal or ok
Looks like little holes
And how do you think these cylinders look for being 14years
Sent from my iPhone using Tapatalk
-
I just want it brought to .30 over if its possible and to get the pistons an gasket from him so a complete top end and a few other odd and ends after that but ill give them a call
-
Im looking to send my cylinders to fast to be bored/honed and was wondering if any one knows about how to do that just send them in with a note or talk to them first?
-
On 10/18/2020 at 7:03 PM, gusto said:
Vforce make more power, I’ve heard the Boyensen last longer (have no personal experience)
fmfbpowercores will be great trail pipes, if your building this for open road but a different pipe
Ok im probably gonna go with the vforce reeds an a .30 bore
i have the fmf torque reeds in it now an they are ok to me
-
I am wondering if any one has used these or if they think their any good or at least better than the stock ones
https://www.ebay.com/itm/291117449719
-
Ok i was looking at the driveline kits an some others too but im running with the fmf gold series fattys an powercore 2.
And im looking for reeds what wiuld be a good set vforce or boyseen
-
Hi im wondering what is a good engine rebuild kit to buy mines currently at .20 over and not sure if it need to be bored more and looking to do it this winter as its been 14 years on the top end and not sure about the bottom thanks
-
I run a oversized radiator on a stock pump with engine ice on a stock motor
-
I believe you can post the pics on tapatalk
not sure about the rest in sure some in will chime in
-
I have all balls on mine
-
I have a ebay radiator in mine forget the brand but it wasn’t expensive and my cuz has a mishimoto in his raptor 700 all been holding up fine just run better coolant in them
Silver lake sand dunes
in Sand Forum
Posted
Ok thanks jayb1rd ill look around an see what there is