GHSTRYDAR
-
Posts
9 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by GHSTRYDAR
-
-
looking to maybe buy some new handlebars and ive heard some good things about the flexx bars but man their expensive. anyone have any thought or experience w them. Also if you recomend them which length and what angle do you recomend when purchasing.
thanks
Do you have the pro tappers on now. I am looking for new bars also. I have been looking at flexx bars also.
-
you want to set your idle off the idle set screws... then you want to sync your carbs by adjusting the pull of the slides using the caps. if you use the caps to hold the idle you can run into problems when you turn the bars, if the cable is too tight it will casue the carbs to open more and rev the motor...
Can some one send a photo of which whole to drill out for the Idle set screww.
I have the cabs aprt and clean I have a piec of wood for insid the carbarrel and I have the drill press set up.
Where do I drill :ninja:
Thanks
jim
-
When I got it all together It starts hard and finally it runs. It backfires out of the right side and then it is puffing coolant thru the exhaust on the right side.
I run a compression test and the right is 147, the left 145.
I ran the compression test by installing the compression tool and kicking the motor over w/ throttle wide open until the needle reaches peak compression.
I pull the head and there was no evidense of the oring passing coolant but there was coolant in the jug.
Here is the background no here are my questions:
1. Was the backfire a syptom of coolant in the chamber or something else?
2. Should I take the head studs out and block sand the jugs top face?
3. If I have to take the studs out how do I do that?
4. Why would a compression test not show the head gasket leak?
-
Custom Gas tank Lettering
5 each single color , 7 each two tone
Yamaha Accent Sticker pack
12 shipped , single color only
Jumbo sticker pack
20 shipped
Banshee RIP sticker
5 shipped ( pick 2 colors )
Fuck 4 strokes
Avalible in single and two tone . 3$ / 6$
Banshee Hq Downright Dirty
6 shipped two tone . pick colors
all prices are excluding chrome * Chrome will be slightly more.
Hey how much for the Rumble Shee stickers? I want to tie my truck into my Banshee :biggrin:
-
Just be carefull when you "whack it ", so that you don't bust a nut, or a bolt. :biggrin:
Wear your saftey glasses, you wouldn't want to get anything in your eyes while you are whacking it
-
Hey I am looking for some one with expirence troubleshooting a Banshee Near Newport News Va.
I do not mind traveling a vcouple of hours. I am not expirenced w/ the 2 stroke and I am having difficulties.
I have a 2003 Banshee that I replaced the impellar w/ a Vitos aluminum impellar. I had a head gasket go and I replaced the head with a Noss unit.
I cleaned the mating surface and followed the installation directions. All orings went in apperently fine. I torqued in the correct pattern at the suggested torque intervals. I am still having the same head gasket symptoms. The local dealer said I could have a cracked jug, however they are not able to tie up shop time. I have gone to the shop several times bu obviously they do not want to get involved.
So I am looking for someone that I can take it to who can show me what to do.
Thanks :biggrin:
-
I am in need a mechancial assistance. Is there anyone near newport newport news VA that would be willing to help me out, I am willing to pay.
Thanks
Jim
-
I am from newport news, I would love to go for a ride somwhere, I have a 2003 special edition blk/yellow Banshee
Thanks
Jim
Hangover question...
in General Banshee Discussion
Posted
don't worry by the time your in your mid 30's you will be on blood pressure meds chloestrol medications and allergy meds and you will not be able to drink a full beer