[This Is Kinda Weird]

The numbers 40:1 for example means 40 parts fuel to 1 part oil. 

 

The best way I have found to mix is get a "Ratio Right" cup.  You can get it a just about any local motorcycle shop.  It has all the ratios on the side of it.  You just choose what you want the desired mixture to be in a certain amount of fuel and fill to that line.  It's as easy as it sounds.

 

I'm with Led.  I use Castor 927 at 40:1 with 110 oct.

 

 

 

 

broke

Dont you have it backwards 40 parts of oil to every 1 gallon of gas is what i thought

[Heads]

Can someone tell me what torque values to torque the head with with a Pounds per square inch torque wrench thats the only wrench i can get ahold of right now. any help would be appreciated.

[Banshee Wont Start]

is the left side firing with no compression or is it not firing at all, check your rings and spark

[Carb. Question]

The fuel injection should be on the top of the motor, find the airbox and trace the hose connected to it back to the other end, and thats where it will be.

[Transmission Shifter Lever Question]

My opinion goes with breaking it in.nueteral is just slightly shifted up after 1st

[Banshee Broke!]

Take your sparkplug off the head and leave it connected to the spark plug wire, have someone kick it while you hold the plug on the engine, if you dont see sparks then it isnt firing

[Help With Suspension.......]

There is also a factor of how much he weighs.

[Banshee Wanted]

I am looking for a 1990 through 2000 banshee that is in good running condition for swap on a 1993 camaro red with grey/black interior nice condition and a good running car.

[Water Pump Problems!]

I have taken the plastic side cover off.. the fins are gone and its just a shaft.. i cannot pull the shaft out its stuck...im not sure what you mean by the front half of the cover.. its all one piece..... more help please

[Water Pump Problems!]

Hey .

 

Any one know how to change a water pump on a banshee. Ive taken the plastic cover off on the side of the crank case . i see the shaft of the old pump. but how do i get it out..

 

 

any help would be appreciated.

 

 

thanks

[Dumb Argument With Me And My Friend.]

Goto this website and type the weight of your atv and its horsepower and this calc will tell your trap speeds of 1/4 mile

 

 

 

 

 

 

 

http://www.torinocobra.com/horsepower.htm

[Dumb Argument With Me And My Friend.]

Goto this website and type the weight of your atv and its horsepower and this calc will tell your trap speeds of 1/4 mile

[Cbr 350 On A Recon Frame.]

I was just going to try it for something to do.

[Looking For Banshee With Problems]

I have a complete engine for 900$

[Prices?]

Nice banshee smokin

[jetting problems]

how exactly does the chokes work in them carbs mine doesnt work

[Banshee T.O.R.S]

what is the safe way to dissconnect the throttle overide on a banshee? also what is the module that is mounted right beneath the flywheel?

[flywheel refuses pop]

What does that little module do right underneath the flywheel it was all flooded in my banshee

[won't start]

How does the choke work on these carbs i looked at mine and all i can see is a small hole on the top of the carb and when you choke it the needle opens the hole up and that is all

[Having engine diffuculties suggestions?]

Thats what im starting to think is wrong is the pilot jets, because i cleaned the carbs they are clean

[custom drag banshee]

how much are you asking for it and what year is it?

[Having engine diffuculties suggestions?]

My banshee doesnt want to start, i have to primer the cylinder with a little bit of gas just to get it started, it acts like it may be due to loss of compression, i currently started to tear it down today to check rings and piston because i recently got it also whenever i have the clutch in whenever you rev it, it just sticks at that rpm and will not drop unless you slightly let of the clutch i have some mechanical knowledge but not awhole lot can someone give me some suggestions.