deathtrap

Thanks for all the replies. I have been very busy at work, but I am finally back at trying to get this thing sorted out. This problem has escalated into the left cylinder firing for about 10 seconds and then stopping while the right is fine. This prompted me to finally do a compression check on both cylinders and I got 135-140 on both. I then pulled the carbs again and everything appears to be in order. I am stumped because it was running fine and after a long ride all of this started. Any more ideas with this new info?

I am located in Bucks County, PA about 10-15 minutes from Philadelphia. I am selling my 2001 Yamaha Banshee. The quad is registered with the Pennsylvania DCNR and I have the clean title in my name. The quad is 100% legal and can be ridden legally in PA state park atv trails. This sale includes the registration sticker and license plate. It starts right up on one or two kicks and needs nothing. Ready to ride! Below is a list summarizing the quad: - 2001 Yamaha Banshee 350 (clean title in hand). - Works shock with remote reservoirs - Toomey T6 exhaust - V-Force reeds - Pro taper bars - Full aluminum skid plates - TM design works poly case saver - Brand new Regina sprokets and chain - Brand new itp wheels and Maxxis Razr 6 ply tires - Brand new oem plastics (full set including rad and tank covers) • The bike is adult owned and maintained. Price is $3000 firm, no trades. Call or Text: 267-3O3-45OO

I have an 01 banshee with toomey t6 exhaust and k&n intake I bought a few months ago. When I got it, I did a carb deep cleaning and rebuild, I also used the toomey perfect jet kit. It ran awesome and I did 3+ hour ride each weekend, but I noticed the next day it was hard to start. Fast forward and now if it sits more than a day, I need to spray pre-mix/gas into the intake. Pilots are 1.5 turns out, the slides are perfectly in sync and it runs great once started and warm. I checked the choke tube and it exists and is intact. Any ideas?

I have a pair of rear 4/156 hubs from an 89-90 banshee. These are commonly used to run a 10" rear wheel setup. They are in excellent condition with both the spline and threads on the stud being in perfect shape. $80 including shipping and paypal fees.

I am not really into the race cut look. I put those maier stock replacement fenders on about a month ago and they fit great with no issues and look awesome.

I need a set of rear banshee hubs stock 4/115 bolt pattern for this weekend. Located in the Philadelphia / South Jersey are. Give me a call of you have set for sale 267-3O3-45OO

$100 shipped. Any takers?

I have a set of sprockets that were removed from one of the bikes I recently purchased. Minimal wear on this set and were removed as part of a part out. 13T front and 41T rear. $20 (shipping and paypal gift included).

I have a set of un opened and unused Boyesen Super Stock reeds. Price is $15 (shipping and paypal gift included).

I have a brand new in packaging Pivot Works front wheel bearing kit part #: pwfwk-y09-000. $20 (shipping and paypal gift included).

I was going to use this setup for ripping around local trails, but have since acquired a different setup in the purchase of my last bike. One wheel has a slight bend (very slight, almost unnoticeable in person, but easy to see in the photos, holds air with no issue and could easily be tapped out). One tire has one plug that was like that when I acquired the set. I had no issues and actually forgot about it until photographing the set (cleaned it up a bit to show). The tread is easily 75%+ with no other issues to speak of. Perfect set for someone looking to test the waters on a 20x11x10 setup. $130 - Price includes shipping and PayPal (gift or add 3% to total).

Just got shipping quotes from UPS, FedEX and USPS. They are way more expensive to ship than I anticipated, so unfortunately I can let them go for under $200 shipped in the U.S. Sorry for any confusion, I have never shipped a set of plastics before so I figured the $165 would cover the cost plus shipping, but I was mistaken.

Im in Bucks County, right outside Philadelphia.

I have switched my bike up a bit and no longer have use for my OEM Yamaha white plastics. They are in great shape with only a few scrapes here and there (nothing that cant be sanded out), there are no bends or cracks of any kind and all of the mounting holes are intact as they should be. Price is $165 shipped in the U.S.

Bump