Mullet Man Posted March 17, 2006 Report Posted March 17, 2006 (edited) i cut mine too. said fuck it. pics are in the image section i'd like to see pics of how yours are shaped after cutting. from what i have seen, there is about 5-6 different ways people do them (for the most part) hell, if i had an extra set i wouldnt hesitate havent ridden it with'em cut yet. but i agree with Wallace, mud and getting dirty/wet comes with the territory on these OFF ROAD vehicles might as well do it on a trick looking shee Edited March 17, 2006 by Mullet Man Quote
phxrider Posted March 23, 2006 Report Posted March 23, 2006 Well everyone that responded I did it I chopped them off. Takes a little while to get used to it but i think i like the way it looks. I will attach a pic latter for everyone to see the new looking shee. Latter. 485853[/snapback] Quote
DIRTMAN350 Posted March 26, 2006 Author Report Posted March 26, 2006 http://i47.photobucket.com/albums/f187/Dir...50/P3260066.jpg http://i47.photobucket.com/albums/f187/Dir...50/P3260058.jpg Well here it is. Got to the link above and see the pics. Latter. Quote
sandman Posted March 27, 2006 Report Posted March 27, 2006 Job well done! That is one very clean '98'. It's obvious you take care of your bike. Quote
DIRTMAN350 Posted March 27, 2006 Author Report Posted March 27, 2006 Yeah that i do. It's my pride and joy. Thanks for the compliments. Quote
dj_diablo54 Posted April 10, 2006 Report Posted April 10, 2006 I was going to cut mine this week just not sure exactly where I should cut them?? Anyone got anh pics of them cutting theres up or before and afters. Quote
Dinner Posted April 12, 2006 Report Posted April 12, 2006 (edited) I was going to cut mine this week just not sure exactly where I should cut them?? Anyone got anh pics of them cutting theres up or before and afters. 500139[/snapback] I did mine in about 10 minutes of cutting, 10-20 minutes of sanding BEFORE: AFTER: My steering looks off because my rods arn't adjusted yet in this pic Edited April 12, 2006 by Dinner Quote
Slayer1018 Posted April 12, 2006 Report Posted April 12, 2006 (edited) Cut them! I'd have someone w/ experience do it... Just don't cut them off like others on this board have... Sorry, but the Banshee right above doesn't look good IMO.... Mine have more style... Mine are some of the nicest you will see Edited April 12, 2006 by Slayer1018 Quote
RIPPEN Posted April 13, 2006 Report Posted April 13, 2006 Cut them! I'd have someone w/ experience do it... Just don't cut them off like others on this board have... Sorry, but the Banshee right above doesn't look good IMO.... Mine have more style... Mine are some of the nicest you will see 501210[/snapback] Ill take that Challange... I cut my own and I would say mine are not the best but I think they give you a run... RIPPEN Quote
Dinner Posted April 13, 2006 Report Posted April 13, 2006 (edited) Cut them! I'd have someone w/ experience do it... Just don't cut them off like others on this board have... Sorry, but the Banshee right above doesn't look good IMO.... Mine have more style... Mine are some of the nicest you will see 501210[/snapback] WHAT!? is your problem .... Just kidding , yea i like the looks of yours, i just didnt want to screw up to bad, so i did it right along the bend (lazyness kicking in) Edited April 13, 2006 by Dinner Quote
RIPPEN Posted April 14, 2006 Report Posted April 14, 2006 Nice bike RIPPEN 501500[/snapback] Thanks man RIPPEN Quote
Hollister_Hitman Posted April 14, 2006 Report Posted April 14, 2006 Yeah Rippin has the best plastics I have seen so far good job on those cuts can you post some more angles? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.