hoppedupandcutdown Posted December 14, 2016 Report Share Posted December 14, 2016 So when I went to put my right slide in, my throttle cable goes slack... I'm not following? Quote Link to comment Share on other sites More sharing options...
Dflynn926 Posted December 14, 2016 Author Report Share Posted December 14, 2016 I'm not following? I pulled my carbs one at a time. I did the left one and put it back no issues. And the thumb throttle felt normal. When I did the right one and put it back on and then when putting the slide and needle back in, when in fine, but after tightening the top, i felt the throttle and it was like it was already compressed. Quote Link to comment Share on other sites More sharing options...
Yamahafan#1 Posted December 14, 2016 Report Share Posted December 14, 2016 Pull it back out and make sure it lined up right. And make sure the rubber seal on to of ur carb caps isnt bent or off pull on the throttle cable. And if slide are in the right carbs u should be able to see the dot in the window on the right sides of ur carbs. Quote Link to comment Share on other sites More sharing options...
Dflynn926 Posted December 14, 2016 Author Report Share Posted December 14, 2016 Ok I'll try pulling it again. When the slide is out of the carb, the cable feels normal. 1 Quote Link to comment Share on other sites More sharing options...
Yamahafan#1 Posted December 15, 2016 Report Share Posted December 15, 2016 Ok I'll try pulling it again. When the slide is out of the carb, the cable feels normal. Then its deff geting hung up on some thing u shouldent realy have to for the carb cap on to screw it on. Quote Link to comment Share on other sites More sharing options...
Dflynn926 Posted December 15, 2016 Author Report Share Posted December 15, 2016 Ok so the slide was 180 degrees off... yup I'm dumb Hahaha. Shee runs now... but it just starts to high idle... is this because I cut the tors wires? Quote Link to comment Share on other sites More sharing options...
Yamahafan#1 Posted December 15, 2016 Report Share Posted December 15, 2016 Ok so the slide was 180 degrees off... yup I'm dumb Hahaha. Shee runs now... but it just starts to high idle... is this because I cut the tors wires? Dose it slowly creep up to a high idle or right off the bat it dose ? Quote Link to comment Share on other sites More sharing options...
J-Madd Posted December 15, 2016 Report Share Posted December 15, 2016 Carbs are out of sync. Quote Link to comment Share on other sites More sharing options...
Dflynn926 Posted December 15, 2016 Author Report Share Posted December 15, 2016 Dose it slowly creep up to a high idle or right off the bat it dose ? Right off the bat Quote Link to comment Share on other sites More sharing options...
Dflynn926 Posted December 15, 2016 Author Report Share Posted December 15, 2016 Carbs are out of sync. How do I sync them without the tool Quote Link to comment Share on other sites More sharing options...
RIPPIN' IT UP Posted December 15, 2016 Report Share Posted December 15, 2016 Adjust idle & air screws Sent from my ZTE T84 using Tapatalk Quote Link to comment Share on other sites More sharing options...
J-Madd Posted December 15, 2016 Report Share Posted December 15, 2016 Take the filter off. And look into the carb. Quote Link to comment Share on other sites More sharing options...
RIPPIN' IT UP Posted December 15, 2016 Report Share Posted December 15, 2016 Visually sync the carbs Sent from my ZTE T84 using Tapatalk Quote Link to comment Share on other sites More sharing options...
Dflynn926 Posted December 15, 2016 Author Report Share Posted December 15, 2016 How do I visually sync them if i can't run it? So I do need to have idle screws after cutting wires? I was under the impression I could at least start it without putting on the elimination kit on Quote Link to comment Share on other sites More sharing options...
J-Madd Posted December 15, 2016 Report Share Posted December 15, 2016 Push the throttle and look at the slides. Make sure they raise and lower at the same time. Adjust the cable on top of one carb to move the slide up or down in the throttle range. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.