stroking
-
Posts
818 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Everything posted by stroking
-
DOES THIS PLUG LOOK OKAY ? its black on one side
-
still got it ?
-
how much power increase can be gained on a stock cylinder drag motor going from stock reeds two V force ?
-
What degree dome does the stock head have ? and what is the best degree domes to use with alky ? 9-12-13 degree ???
-
paypal is [email protected]
-
its got BRANDNEW o-rings installed on it,have not been ran yet
-
Im selling because i have two and dont need this one only problem is one dome has alittle pitting in it...still useable to me.........has been polished also $75 shipped text or call for more info.....843-303-0898 paypal is [email protected]
-
IM posting this up for a friend that needs a stock banshee engine. 2002 zx 6 this engine runs good but needs stator and cover,the bike was wrecked and total so he pulled the engine stator and cover was damaged in wreck. will take $600 OBO also call anytime for more info 843-336-3289 todd
-
yes,i have paypal text or call me for payment and shipping info 843-303-0898
-
the stinger on one has been replaced so that measurement wont be right,but i can measure behind the flange
-
both are not stamped one has nothing on it
-
anybody ever use langcourt for nikasil?
stroking replied to Alex29573's topic in Banshee Repairs and Mods
i have used them two ...... there fast and good + cheaper weld to two cracks in a cub cylinder and replate for $320 -
put i pulled this off a banshee im using for drag racing so i dont need it....its adjustable and straight no bends it was chromed but the chrome was flaking off so its now ceramic coated $60 + shipping or may trade for something
-
I have to CPI drag pipes here and want to know the difference........one is stamped CPI and the other is NOT. Also how can i tell if one is a small bore vs big bore ?
-
i have a override already but i dont want to use a lockup IF i dont have to. its not a big motor, YET!
-
I need to replace some broken reeds but i dont know what kind these are. can i get some help? and where can i buy some new peddles?
-
IS it a must to run a lockup with a override tranny ?? does anyone have a override with a regular clutch setup ? whats the best clutch to use also ?
-
wicked told me a few years ago that a lockup is NOT needed unless your running a 10mil cub or bigger motor.
-
im thinking about test out some 39mm on a stock cylinder stock stroke motor and see how it does against some 34mm
-
the 39mm's rev'ed much cleaner but the power was not there the 37mm's would blow alky out the pipes when you rev'ed it and you could only make two full pass on almost a gallon of alky and make 4-5 with the 39mm's seems like the 37 were dumping way more fuel but both have the same size main and dump tubes with power jets wide open
-
i tried some pwk 39mm on alky on a 4mil cub vs 37mm flatslide mik and you could clearly feel the 37mm were faster and accelarated hard maybe it the flatslide affect that i was feeling
-
How you know when you have too much carb for your motor ? what would be one of the signs of too much ? bogging/no bottomend/no topend would these be goodfor a 4mil cub=37-39mm 4mil stock cylinder=33-35mm or can you just throw some 41mm on a stockcylinder and be good to go ?
-
SOLD!!
-
does R-50 mix with alcohol ?
-
Got a set of pro c and t-6 pipes in very good shape that i want to trade for some out of frame drag pipes i'll get picture up later call or text 843-303-0898 or 843-693-9161