Deets Posted January 9, 2020 Report Share Posted January 9, 2020 10 minutes ago, the boris said: If you didn't do some extreme mods, like porting, pipes, shaving head, you probably don't have to weld it. Sent from my VOG-L29 using Tapatalk 65 mm bore single K&N no lid T5’s as of now Reeds and Timing advance in the near future 1 Quote Link to comment Share on other sites More sharing options...
Deets Posted January 17, 2020 Report Share Posted January 17, 2020 Decided to go with the adjustable plate. also not sure why my pics turn sideways when I post em here? Quote Link to comment Share on other sites More sharing options...
Deets Posted January 18, 2020 Report Share Posted January 18, 2020 So... dude I bought the bike from failed to mention that he put a timing plate in when I asked for ALL of the mods he did. so now I have this one that I don’t need. Unless it fits a blaster too? Wishful thinking probly Quote Link to comment Share on other sites More sharing options...
the boris Posted January 18, 2020 Report Share Posted January 18, 2020 So... dude I bought the bike from failed to mention that he put a timing plate in when I asked for ALL of the mods he did. so now I have this one that I don’t need. Unless it fits a blaster too? Wishful thinking problyLooks quite different from the one on blaster, just sell it. Sent from my VOG-L29 using Tapatalk Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted January 20, 2020 Report Share Posted January 20, 2020 Is the one on the bike cast or billit? If it’s cast, definitely put the Mattoon one on there. Quote Link to comment Share on other sites More sharing options...
Deets Posted January 20, 2020 Report Share Posted January 20, 2020 It is a cast one on there now. Junk? Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted January 22, 2020 Report Share Posted January 22, 2020 On 1/20/2020 at 5:23 AM, Deets said: It is a cast one on there now. Junk? Usually. Some times the bolt hole eyelets crack and then let the plate loose. Then it bounces off the stator and flywheel. It can get pricey real quick. Quote Link to comment Share on other sites More sharing options...
Deets Posted January 22, 2020 Report Share Posted January 22, 2020 Thanks, I’ll get it swapped out. There is a line in the casting, I’m assuming that is where you orientate the timing from. Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted January 23, 2020 Report Share Posted January 23, 2020 15 hours ago, Deets said: Thanks, I’ll get it swapped out. There is a line in the casting, I’m assuming that is where you orientate the timing from. The line where the case halves meet is what you dial the plate to. +4 is pretty widely used on pump gas motors with out a ton of compression. You have a real flywheel puller, right? Quote Link to comment Share on other sites More sharing options...
Deets Posted January 23, 2020 Report Share Posted January 23, 2020 3 hours ago, trickedcarbine said: The line where the case halves meet is what you dial the plate to. +4 is pretty widely used on pump gas motors with out a ton of compression. You have a real flywheel puller, right? Yup, I figured that was the line. yeah I bought one off eBay Quote Link to comment Share on other sites More sharing options...
Jocelyn lapointe Posted December 22, 2020 Report Share Posted December 22, 2020 Is someone know the bolt size for the pick up coil because I will need 2! When I try to unscrew the pickup coil from the oem plate I stripped the bolt and need to know the size and thread and length of the bolt? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.