banshee440 Posted September 4, 2008 Report Share Posted September 4, 2008 Ok so as some of you guy's already no i'm starting to put my blown up mess back together.. I'm starting with stock cases a stock crank not welded and now i only need cylinders so i was gave a set of 69mm bore juggs wich i can tell they are ported not sure how much but a noticeable amount more than my blown up stockers.. So here where i'm stuck what am i goin to have to do to run these big bore juggs that are ported i have stock carbs a noss head that i no i need big bore cut domes for but what are the pros and cons?? What size carbs? what cc for the cut domes? i'm 500 above sea level and i'm stickin to pump gas.. I'm sure theres tons i'm missing so Any input would be great Thanks again guy's... Quote Link to comment Share on other sites More sharing options...
jar banshee 01 Posted September 4, 2008 Report Share Posted September 4, 2008 i don't know for sure but i think your gonna have to run race gas Quote Link to comment Share on other sites More sharing options...
shanYE west Posted September 4, 2008 Report Share Posted September 4, 2008 Going to have to get with Dave @ Noss and find out if he makes domes for the 69mm bore.. I know Trinity heads go bigger.. but i'm not sure how far past 68mm the Noss domes go. Quote Link to comment Share on other sites More sharing options...
Onesickcrewcab Posted September 4, 2008 Report Share Posted September 4, 2008 Thats kind of an odd sized piston. Going to take special domes for sure. Wonder if there going to be able to cut them that wide and not have sealing problems. Do you have pistons for it already? If not do you know what pistons they take? Curious. Quote Link to comment Share on other sites More sharing options...
banshee440 Posted September 5, 2008 Author Report Share Posted September 5, 2008 No i don't have pistons for them but the guy i got them from said they had 69mm sleeves in them and they were ported to match.. But had no clue on what stage porting was done on them... Quote Link to comment Share on other sites More sharing options...
kawiking Posted September 5, 2008 Report Share Posted September 5, 2008 id find out who makes a 69mm sleeve .... id start calln somebuilders and see what they say. call.f.a.s.t or k&t .. trinity ,passions. somebody that can get u some info. Quote Link to comment Share on other sites More sharing options...
banshee440 Posted September 5, 2008 Author Report Share Posted September 5, 2008 Ok any one got a number for f.a.s.t or any michigan builders.. Thanks Quote Link to comment Share on other sites More sharing options...
spurdy Posted September 5, 2008 Report Share Posted September 5, 2008 Ok any one got a number for f.a.s.t or any michigan builders.. Thanks http://www.farmandsandtoys.com/index.asp SP Quote Link to comment Share on other sites More sharing options...
dajogejr Posted September 5, 2008 Report Share Posted September 5, 2008 Ok any one got a number for f.a.s.t or any michigan builders.. Thanks Dan Hull @ A&S: http://www.bansheeracing.com/ Rob Earl @ RDZ: http://www.rdzracing.com/Main/main.htm Bob @ RB Porting: http://groups.msn.com/RBRacingTwoStrokePorting These are all Michigan guys, all within an hour of Lansing area... Quote Link to comment Share on other sites More sharing options...
shanYE west Posted September 5, 2008 Report Share Posted September 5, 2008 I'd add Vito's to that list.. If those are 69mm bores vito's has the pistons for them. Quote Link to comment Share on other sites More sharing options...
banshee440 Posted September 5, 2008 Author Report Share Posted September 5, 2008 Thanks again guy's... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.