Jump to content

Banshee802

Members
  • Content Count

    188
  • Joined

  • Last visited

  • Days Won

    1

Banshee802 last won the day on June 25 2019

Banshee802 had the most liked content!

Community Reputation

10 Good

About Banshee802

  • Rank
    HQ Soldier
  • Birthday 05/28/2000

Profile Information

  • Gender
    Male
  • Location
    Vermont
  • Interests
    Banshees

Previous Fields

  • My Banshee (optional)
    Red, 1998, Toomey T5, VForce reeds

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Banshee802

    Toomey T5 hitting cylinder

    I already have the front spaced out and it still hits. How would I go about bending it? Sent from my iPhone using Tapatalk
  2. Banshee802

    Toomey T5 hitting cylinder

    Nobody can help? Sent from my iPhone using Tapatalk
  3. Banshee802

    Right pipe cold at idle. Warms up some when riding

    Have you completely disassembled the carbs and let them soak or put them in a ultrasonic cleaner? Or did you just spray them with carb clean. I think your right carb might have a plugged up port if it was running fine then went to shit. Or double check compression and reeds Sent from my iPhone using Tapatalk
  4. Banshee802

    Stock ‘95 been sitting for 5-6 years

    You drain out trans oil and coolant? Good chance if it wasn’t stored correctly or started now and again the seals and bearings might be gone. •drain all fluids •dump some oil down into the cylinders •take off carbs and clean them out •inspect and remove reeds •inspect cylinders\pistons •fresh spark plugs •fresh fluids I would do something along those lines. If you can’t get it going then check compression and start looking at the electrical. Sent from my iPhone using Tapatalk
  5. Banshee802

    Right pipe cold at idle. Warms up some when riding

    Spark good on that side? Sounds like a fuel issue. Your fuel lines flowing evenly? You have your choke tube in between both carbs? Sent from my iPhone using Tapatalk
  6. Alright. Been having this issue where my left T5 hits right where my cylinder and head meet. Constantly rubbing against it. I’ve tried to space the pipe mount out with washers, but still hits. Anyone else run into a issue like this before?? Any fix suggestions Sent from my iPhone using Tapatalk
  7. Banshee802

    Bent frame

    What year is that one? Is that powder coated?
  8. Banshee802

    Bent frame

    Were you able to take a look at those frames?
  9. Banshee802

    Banshee won't start fuck my life

    I mean yes, but it’s around 50 degrees where I am now and my banshee is having a harder time starting. But you said it might be compression too. First check spark. Ground the plug on head bolt and make sure it’s sparking. If that’s good, then check compression. If good then it’s a fuel problem Sent from my iPhone using Tapatalk
  10. Banshee802

    Banshee won't start fuck my life

    Compression test it. You rejet for colder weather? Sent from my iPhone using Tapatalk
  11. Banshee802

    Bent frame

    Aarms are brand new. Has to be the mounts and the frame Sent from my iPhone using Tapatalk
  12. Banshee802

    Bent frame

    Maybe this picture is better Sent from my iPhone using Tapatalk
  13. Banshee802

    Bent frame

    I know the left side is suppose to be different from right straight out of factory. But my whole front end is pushed to the right. My aarms and shocks are up higher on one side. Along with the wheel. Tapatalk is reducing the quality of the picture so it’s hard to see Sent from my iPhone using Tapatalk
  14. Banshee802

    Banshee won't start fuck my life

    Key, killswitch, and gas all in the right position? Have you checked to see if it has spark? Any major temperature changes near you Sent from my iPhone using Tapatalk
  15. Banshee802

    Bent frame

    Ok. I’m in Vermont. Might be looking for a new one. Prices and what years are they? Sent from my iPhone using Tapatalk
×